manualshive.com logo in svg

Olivetti d-Copia 12, Service Manual

Share
Download
Olivetti d-Copia 12 Service Manual Download Page 60

6-6

Service Manual

Y101700-5

Content

Main motor system ON + Cooling fan low speed
(Operation/Procedure)
When the START key is pressed, the main motor is rotated for 30 sec.
To save toner consumption, the different operations are executed depending on
installation of the developing unit.
• When the developing unit is installed, the developing bias, the main charger, and the

grid are also outputted.

• When the developing unit is not installed, only the motor is rotated.

* Do not turn on the door open/close switch forcibly to execute this simulation.

Polygon motor ON
(Operation/Procedure)
When the START key is pressed, the polygon motor is operated for 30sec.

Manual feed setup
(Operation/Procedure)
1. When this simulation is executed, the currently set bypass code number is displayed.
2. Enter the code number corresponding to the bypass and press the START key, and

the setting will bechanged.

Code number

Bypass

0

Single bypass

1

Multi bypass

SPF setup
When this simulation is executed, the currently set SPF code number is
displayed. Enter the code number of the SPF to be set and press the PRINT switch. The
setup is changed.

Code number

SPF

0

Without SPF

1

With SPF (Setup required
when installing FAX)

2

With RSPF

Second cassette setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the second

cassette is displayed.

2. Enter the code number and press the Start key. The setting is changed.

Code number

Second cassette

0

Without second cassette

1

With second cassette

Main code

25

26

Sub code

01

10

01

02

03

Summary of Contents for d-Copia 12















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands