manualshive.com logo in svg

Olivetti d-Copia 12, Service Manual

Share
Download
Olivetti d-Copia 12 Service Manual Download Page 59

Y101700-5

Service Manual

6-5

Content

Maintenance/mini-maintenance counter display
The display is the same as the total counter value display.
When the destination is set to other than Japan AB series, the maintenance counter is
displayed.
When the destination is set to Japan AB series, the mini-maintenance counter is
displayed. The display is the same as the total counter value display.

Maintenance/mini-maintenance preset display
The preset value corresponding to the code set in 21-01 and 21-02.
The display is the same as the total counter value display.
When the destination is set to other than Japan AB series, the maintenance preset value
is displayed.
When the destination is set to Japan AB series, the mini-maintenance preset value is
displayed.

Total counter display
The total count value is displayed in 3 digits 2 times repeatedly.
<Display example: 12345>
012          Blank         345        Blank         012
0.7s          0.3s            0.7s        1.0s          0.7s

Developer counter display
The display method is the same as the total count value display.

Drum counter display
The display method is the same as the total count value display.

P-ROM version display
The P-ROM version is displayed in 3 digits on the value display section.
(100% Zoom lamp display)

Developer counter clear
When the PRINT switch is pressed, the drum count value is reset to 0.

Drum counter clear
When the PRINT switch is pressed, the drum count value is reset to 0.

Main code

22

24

Sub code

01

02

05

06

12

14

06

07

→

→

→

→

→

→

→

→

→

→

→

→

→

→

→

→

→

→

→

→

Summary of Contents for d-Copia 12















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands