background image

5.OPERATING THE SPEED DOME

FIRMWARE  V2.61
Protocol: PELCO
Dome Address: 001
Comm 9600,N,8,1

Initial Screen

After powering up, the camera will enter the 
self-test mode and display the status screen( 
as in the picture left).It contains information 
about the model and current settings.

- V2.61:

 Current firmware version

- Protocol:

 control protocol which currently used

- Dome address:

 Address ID of speed dome. please refer to the section "Protocol 

setup " for details.

- Comm 9600,N,8,1: 

current setting of the serial communication interface.

9600:

 Baud rate. please refer to section "Baud-Rate setup" for details

N, 8, 1:

 No parity bit, 8 bit length, 1 stop bit. this setting can not be changed 

Operation  Screen

The intial screen will stay remain on until any user action is being taken. If the power-
up action is set, the initial info wil vanish immediatly.

32.0

CAM TITLE

ZONE-1

285   78

18X

Pan degree

Zoom factor

Tilt degree

Zone description

Temperature

4.INSTALLATION

Optional bracket accessories

The PTZ cameras can be equipped with various bracket accessories for indoor 
and outdoor installation. please contact your distributor for further details.

Corner 
Mount

Pole 
Mount

Wall mount and
 Power box

Ceilling 
mount

Indoor Wall
mount

Outdoor
Power  Box

Indoor ceilling
mount

Extended wall
mount

Swan-Neck
Mounting 
bracket

Wall
mount

Installing the core unit to base board.

The PTZ camera core unit and base board are packed seperatly, in order to be 
protected through the transportation. After unpaking and during the installation, the 
core unit should be installed as following:

Installing the core unit by 
pushing  into the 
housing.please note the 
position  of connector. For 
releasing, please press the 
lever-lock to core and pull off 
the unit.

Lever-
Lock

Connector
Interface

Power
LED

Metal 
Clip

WARNING:
Do not pull or hold the connector interface with force. It 
is design only to connect the core unit and the base 
board. Any presure on connector will cause damage and 
avoids the warranty.

PTZ operation

 For the surveillance operation, the dome can be controlled from a keyboard device, 
Multiplexer or DVR  through RS-485 Interface. Make sure that the cable is connected 
and the settings (baud rate, Address ID and protocol) of both keyboard and the dome 
are configured correctly. For more description about the PTZ operation, please refer 
to the user’s manual of the keyboard.

Safety spring

Rubber ring

 cable

Heater connector

Once the base board is connected to power, 
the power LED will light.

Heater connector 
on outdoor 
housing

Outdoor
housing cover

Screws

Some products may not be available in your country, please contact our distributor for more details

Some products may not be available in your country, please contact our distributor for more details

9

10

Indoor 
embedded
mount

The operation screen can display additional 
information. 

Temperature: current temperature inside the 
speed dome( °C)
Cam title:        User definable camera title
Zone:             Current zone name
Pan deg.:       Pan angle, 0-359°
Tilt deg.:          Tilt angle, 0-90°
Zoom Factor:  Zoom factor

Display of the information can be activate or 
deactivate through the OSD menu. please refer to 
the system setting for detais.

Summary of Contents for SP27HB-V55DN
















Reviews: