4
Federal Communications Commission
Radio Frequency Interference Statement
for 230/240-Volt Models
WARNING: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
It is the responsibility of the user to obtain the required shielded
cable in order to ensure compliance of this equipment with FCC
regulations.
Changes or modifications not expressly approved by Okidata may
void your authority to operate this device.
Safety Instructions
Your OKI printer has been carefully designed to give you years of safe,
reliable performance. As with all electrical equipment, however, there are
a few basic precautions you should take to avoid hurting yourself or
damaging the printer:
• Read the setup instructions in the Quick Setup guide carefully. Be sure
to save it for future reference.
• Read and follow all warning and instruction labels on the printer itself.
• Unplug the printer before you clean it. Use only a damp cloth; do not
use liquid or aerosol cleaners.
• Place your printer on a firm, solid surface. If you put it on something
unsteady, it may fall and be damaged; if you place it on a soft surface,
such asa rug, sofa, or bed, the vents may be blocked, causing the printer
to overheat.
• To protect your printer from overheating, make sure all openings on
the printer are not blocked. Don’t put the printer on or near a heat source,
such asa radiator or heat register. Keep it out of direct sunlight. Allow
enough room around the printer for adequate ventilation and easy access
to the paper trays.
• Do not use your printer near water, or spill liquid of any kind into it.
• Be certain that your power source matches the rating listed on the back
of the printer. If you’re not sure, check with your dealer or with your
local power company.
• Your printer has a grounded, 3-prong plug as a safety feature, and it
will only fit into a grounded outlet. If you can’t plug it in, chances are
you have an older, non-grounded outlet; contact an electrician to have
the outlet replaced. Do not use an adapter to defeat the grounding.
• The printer must be installed near a power outlet which remains easily
accessible.
• To avoid damaging the power cord, don’t put anything on it or place it
where it will be walked on. If the cord becomes damaged or frayed,
replace it immediately.
• If you are using an extension cord or power strip with the printer, make
sure that the total of the amperes required by all the equipment on the
extension is less than the extension’s rating. The total ratings of all
equipment plugged into the outlet should not exceed 15 amperes.
• Do not poke anything into the ventilation slots on the printer; you could
get a shock or cause a fire.
• Aside from the routine maintenance described in the online manual,
don’t try to service the printer yourself; opening the cover may expose
you to shocks or other hazards.
• Do not make any adjustments other than those outlined in the online
manual: you may cause damage requiring extensive repair work. See
the online manual for information on how to get your printer serviced
by qualified OKI technicians, or call 1-800-OKI-DATA for the location
of your nearest service center.
If anything happens that indicates that your printer is not working properly
or has been damaged, unplug it immediately and follow the procedures in
the online manual for having your printer serviced.
These are some of the things to look for:
• The power cord or plug is frayed or damaged.
• Liquid has been spilled into the printer, or it has been exposed to water.
• The printer has been dropped, or the cabinet is damaged.
• The printer does not function normally when you are following the
operating instructions.
Federal Communications Commission
Declaration of Conformity
for 120 Volt Models
1. Product Identification
OKIPAGE 8z, model EN8067A or EN8067B
2. Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
3. Responsible Party
Oki Data Americas, Inc.
2000 Bishops Gate Boulevard
Mt. Laurel, NJ 08054-4620
1-800-654-3282 (1-800-OKI-DATA)
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
It is the responsibility of the user to obtain the required shielded cable in
order to ensure compliance of this equipment with FCC regulations.
Changes or modifications not expressly approved by Oki Data may void
your authority to operate this device.
Industry Canada
Radio Interference Statement for 120-Volt
Models
This apparatus complies with the Class “B” limits for radio interference
as specified in the Industry Canada Radio Interference Regulations.
