background image

Replacing Consumables / Maintenance Units

- 57 -

2

1

3

4

5

6

7

Recommended Schedule for Replacing the 
Image Drum Cartridge

When the image drum cartridge nears the end of its lifespan, 
the message [*Image Drum Near Life] (* represents the 
specific color) will appear on the control panel to notify you that 
it is time to prepare a new image drum cartridge. You can 
continue printing until the message [Install new * Image Drum]
(* represents the specific color) appears, then printing will stop.

Memo

• After the message [Image Drum Near Life] appears, you can 

continue to print before the message [Install new Image 
Drum] appears.

• When the toner is almost gone, you may not be able to 

resume printing, even by opening and closing the top cover.

Note

• Use new image drum cartridges. Print quality may 

deteriorate if more than a year has passed since the 
cartridge was opened.

• Even after the message [Please open/close top cover] 

appears, you can continue to print if there is still toner, by 
opening and closing the top cover.

• If toner runs low after the message [Please open/close top 

cover] appears, the same message will appear again if you 
continue to print. Depending on your settings, the toner 
might run low before the message [Please open/close top 
cover] is displayed.

• Envelopes, post cards, labels and thick paper may use the 

color drum, even when the grayscale setting is used.

• If the [ADMIN] > [GENERAL] > [STATUS MESSAGE] > 

[SUPPLIES NEAR LIFE MESSAGE] from the Management 
Setting menu is set to [Disable], the message [Image Drum 
Near Life] will not appear.

• To get the best performance from your machine, please 

genuine Okidata consumables.

• For best results, use genuine Okidata consumables. If you 

use 3rd party consumables, you may experience problems 
or unsatisfactory print quality. Service for problems caused 
by use of 3rd party consumables is not covered by the 
warranty or the maintenance contract. (Use of 3rd party 
consumables does not always cause problems, but please 
exhibit caution when using them.)

Replacing the Image Drum Cartridge

1

Hold the handle and lift the scanner part.

2

Press the top cover open button to open 
the top cover.

3

Remove the old image drum cartridge.

(1)

Identify the old image drum cartridge by its 
label color.

(2)

Remove the image drum cartridge (with 
the toner cartridge attached). 

Scanner part

Handle

There is a risk of getting burned.

Do not touch the fuser unit. It can be extremely hot.

Caution

Top cover

Top cover open button

Image drum 
cartridge

Summary of Contents for MC770x















































































Reviews: