Oki MC573 Advanced Manual Download

Page: 406 / 507

- 406 -

11. Utility Software

Web Page of This Machine

You can make network settings or menu settings from the Web page of this machine.

• Open the Web Page of This Machine
• Log In as the Administrator
• Changing the Administrator Password (Web Page)
• Checking or Changing the Settings of This Machine
• Encrypting Communication with SSL/TLS
• Encrypting Communication with IPSec
• Limiting by Using an IP Address (IP Filtering)
• Limiting by Using a MAC Address (MAC Address Filtering)
• E-mail Alert
• Using SNMPv3
• Using IEEE802.1X (Wired LAN)
• Setting IEEE802.1X (Wireless LAN)
• Setting Wireless LAN (WPA/WPA2-EAP)
• Setting the LDAP Server
• E-mail Setup
• Setting Power Save Mode (Web Page)
• Setting Sleep Mode (Web Page)
• Setting Auto Power Off Mode (Web Page)
• Registering a Destination (Profile) (Web Page)
• Changing a Destination (Profile) (Web Page)
• Deleting a Destination (Profile) (Web Page)
• Forwarding Received Document Data to an E-mail Destination or Shared Folder (Auto

Delivery)

• Saving Sent and Received Data (Transmission Data Save)
• Fax Reception Notification
• JOB MACRO (Web Page)
• About Items That Can be Set or Checked

• About the Operating Environment

• Check whether your browser is set as follows.

• Set the security setting for the Web page to the middle level, or enable Cookie.

• To enter the [Admin Setup] menu, the administrator password is required.

• To change settings of the machine on the Web page, you must log in as the administrator of the machine.

The description uses the following environment as an example.

• Device name: MC573

• IP address of the machine: 192.168.0.2

Start a Web browser.

Enter "http://(The IP address of this machine)" in the address bar, and then
press the <Enter> key.

About the IP Address of this machine, refer to "Printing a Report to Check".

If the IP address includes a value in one or two digits, do not enter "0" before the value. Communications may not
be performed correctly.

• An example of a correct entry: http://192.168.0.2/

• An example of an incorrect entry: http://192.168.000.002/

Open the Web Page of This Machine

Summary of Contents for MC573




























































































































































































































































































































































































































































































































Search results

Summary of Contents for MC573

Reviews:

Related manuals for MC573

Brands by name

Popular brands

Oki MC573, Advanced Manual

Search results

Summary of Contents for MC573

Reviews:

Related manuals for MC573

Brands by name

Popular brands