Oki MB472dn, User Manual

Page: 583 / 1137

image that is stored in the memory of this machine.
Other
Settings
Redial Tries 2 time(s) Sets the number of redial attempts.
Available range: 0 to 9 times
Redial Interval 1 minute(s) Sets the time between redial attempts.
Available range: 0 to 5 minutes
Block Junk
Fax List
Setting OFF Sets Block Junk mode Fax.
Registered
List
Register/Edit (NULL) Register/Edit addresses for Block Junk Fax.
Display condition: To set [Mode2] or [Mode3], [Admin Setup] >
[Other Settings] > [Block Junk Fax List] > [Setting].
Delete Delete addresses for Block Junk Fax.
Display condition: To set [Mode2] or [Mode3], [Admin Setup] >
[Other Settings] > [Block Junk Fax List] > [Setting].
Ring Response 1 Ring Sets the number of rings required before receiving an incoming
fax.
Dialing Pause Duration 2 second(s) Sets the dial pause time.
Available range: 0 to 10 seconds
Rx Reduc. Rate Auto Sets the reception reduction rate.
Reduc. Margin 24 mm (0.9
inch) or
100 mm (3.9
inch)
Sets the threshold level of reception reduction.
Available range: 0 to 100 mm (0 to 3.9 inches)
ECM Mode ON Sets whether to use the error correction mode.
PreFix (NULL) Sets the dialing prefix. You can enter up to 40 digits.
Received Time Stamp OFF Sets whether to print the time stamp on received faxes.
Print Check Message ON Sets whether to report the error content if a transmission error
occurs.
Fax
Setting
Service Bit OFF If set to OFF, some menu items are not displayed on the screen.
Country Code International
or U.S.A
Sets the country code.
A/R Full Print ON Sets whether to print the list of the communication results
automatically after every 50 communications.
Tone For Echo (For Transmission) Disable Displays only if Service Bit is ON.
Tone For Echo (For Reception) Disable Displays only if Service Bit is ON.
H/Modem Rate(For Tx) 33.6 Kbps Sets the default modem reception transmission speed while the
machine is sending a fax.
H/Modem Rate(For Rx) 33.6 Kbps Sets the default value of the modem transmission speed while
the machine is receiving a fax.
Attenuator 10 dB, Range:
0 - 15 dB
Enter Attenuator. Displays only if Service Bit is ON.
MF Attenuator 8 dB, Range: 0
- 15 dB
Enter MF(Tone) Attenuator. Displays only if Service Bit is ON.
Pulse Make Ratio 40%, Range:
33, 39, 40%
Sets to make rate of DP (10 pps) during call. Displays only if
Service Bit is ON and Tone/Pulse setting is PULSE.
Pulse Dial Type N, Range: N,
10-N, N+1
Sets the pulse type for dialing. Displays only if Service Bit is ON
and Tone/Pulse setting is PULSE.
MF(Tone) Duration 100 mseconds,
Range: 75, 85,
100 mseconds
Enter MF(Tone) Duration. Displays only if Service Bit is ON and
Tone/Pulse setting is TONE.
Calling Timer 60 mseconds,
Range: 1 -
255 seconds
Displays only if Service Bit is ON.
PBX Line OFF When connecting to PBX (internal exchange), put it to [ON].
Forwarding
Setting
Forwarding Setting OFF Sets whether to enable the fax forwarding mode.
Forwarding Number (NULL) Sets a fax number used for the fax forwarding mode.
TAD Mode Type 3 Sets an operation type in Tel/Fax Ready mode.
[Type 3]: A fax signal is detected in 15 seconds from when the
answering machine answers. Normally, use this type.
582