Oilon EasyAce Operation Manual Download

Page: 50 / 54

7.2 Troubleshooting connection problems

Troubleshooting checklist

In case of a problem, check the following:

● The power cable is connected and the power indicator is lit.

● The cloud connection LED indicator is lit.

● Only if a cloud connection is used (hub connected through the internet).

● The Wi-Fi LED indicator is lit.

● LAN cable is connected.

● WAN cable is connected.

● Only if a wired internet connection is used.

EasyAce data hub ver. 2

Restarting the data hub

Turn off the hub’s power and wait for approximately one minute:

● Shut down the entire heat pump from the heat pump’s main switch, or

● Disconnect the data hub’s power cable.

If the problem persists, reset the data hub.

Resetting the data hub

Press and hold the

Reset

button for 3–4 seconds.

Once the hub has been reset, you will need to re-establish the heat pump connection.

48 (49)

M8004 2308EN

Summary of Contents for EasyAce























































Search results

Summary of Contents for EasyAce

Reviews:

Related manuals for EasyAce

Brands by name

Popular brands

Oilon EasyAce, Operation Manual

Search results

Summary of Contents for EasyAce

Reviews:

Related manuals for EasyAce

Brands by name

Popular brands