OHAUS Ranger R21PE15 Instruction Manual Download Page 26

Page: 26 / 44

EN-24

Ranger™ 2000

Series

Content

[

CONtNt

]

Define the content of the printed data.

Result

Set the status.

OFF

= disabled

= the displayed reading is printed

Gross

Set the status.

OFF

= disabled

= the gross weight is printed

Net

Set the status.

OFF

= disabled

= the net weight is printed

Tare

Set the status.

OFF

= disabled

= the Tare weight is printed

Header

Set the status.

OFF

= disabled

= the Header is printed

Note

: See section 7.3.1 for instructions how to enter Header line.

Footer

Set the status.

OFF

= disabled

= the Footer is printed

Note

: See section 7.3.1 for instructions how to enter Footer line.

Mode

Set the status.

OFF

= disabled

= the Mode is printed

Unit

Set the status.

OFF

= disabled

= the Unit is printed

Info

Set the status.

OFF

= disabled

= the Reference Information is printed

Summary of Contents for Ranger R21PE15













































Search results

Summary of Contents for Ranger R21PE15

Reviews:

Related manuals for Ranger R21PE15

Brands by name

Popular brands

OHAUS Ranger R21PE15, Instruction Manual

Search results

Summary of Contents for Ranger R21PE15

Reviews:

Related manuals for Ranger R21PE15

Brands by name

Popular brands