OHAUS Ranger R21PE15 Instruction Manual Download Page 13

Page: 13 / 44

Ranger™ 2000

Series EN-11

4. Manually reset the countdown timer by pressing the

Function

key. [

rEAdY

]

(Ready) will then be displayed.

Note

: If Set0 has been selected, the countdown timer is not displayed. The first

weight larger than 5d will be displayed and held.

Semi-automatic operation

(DYNAMIC is set to SEMI in the Mode menu):

1. Press and hold

Mode

until [

dYNAmM

] (Dynamic) is displayed. [

rEAdY

] (Ready)

will then be displayed.

2. Place the load on the pan to start measurement.

During the average period, the countdown timer decreases in one second

increments.

3. After completed countdown, the average weight will be displayed. The tilde

symbol will blink indicating that the current weight is being held.

4. Manually reset the countdown timer by pressing the

Function

key. [

rEAdY

]

(Ready) will then be displayed.

Note

: If Set0 has been selected, the countdown timer is not displayed. The first

weight larger than 5d will be displayed and held.

Automatic operation

(DYNAMIC is set to AUTOMATIC in the Mode menu):

1. Press and hold

Mode

until [

dYNAmM

] (Dynamic) is displayed. [

rEAdY

] (Ready)

will then be displayed.

2. Place the load on the pan to start measurement.
During the average period, the countdown timer decreases in one second

increments.

3. After completed countdown, the average weight will be displayed. The tilde

symbol will blink indicating that the current weight is being held.

4. Remove the load and the display will reset after 10 seconds, [

rEAdY

] (Ready)

will then be displayed.

Notes

: If Set0 has been selected, the countdown timer is not displayed. The

first weight larger than 5d will be displayed and held.

Alternatively, the display may be manually reset by pressing the

Function

key.

Summary of Contents for Ranger R21PE15













































Search results

Summary of Contents for Ranger R21PE15

Reviews:

Related manuals for Ranger R21PE15

Brands by name

Popular brands

OHAUS Ranger R21PE15, Instruction Manual

Search results

Summary of Contents for Ranger R21PE15

Reviews:

Related manuals for Ranger R21PE15

Brands by name

Popular brands