Ofs Obeya Assembly Instructions Manual Download Page 39

Page: 39 / 44

ofs.com

imagine a place®

800.521.5381

Assembly instructions

Obeya assembly instructions

Fixed rail

Static curtain

Magnetic rail

1. Unroll the static curtain to expose the mounting rail.

2. Remove the magnetic rail from the fixed rail by pulling opposite directions

on both rails.

3. The curtain panel can be removed from the fixed rail if desired by pulling the

top corner of the curtain separating the velcro mounting strip.

4. Locate the fixed rail in the desired position in the width of the wall opening on

the underside of the structures beam trim rail and inset 1/2" from the face of the
cladding panel then attach using #8 x 5/8" wood screws through the 3-L brackets
into the bottom of the beam trim rail.

5. Re-attach the curtain panel if removed using the velcro mounting strip.

6. Align the magnetic rail with the fixed rail and snap into place via the

attached magnets.

Static curtain attachment

Summary of Contents for Obeya













































Search results

Summary of Contents for Obeya

Reviews:

Related manuals for Obeya

Brands by name

Popular brands

Ofs Obeya, Assembly Instructions Manual

Search results

Summary of Contents for Obeya

Reviews:

Related manuals for Obeya

Brands by name

Popular brands