manualshive.com logo in svg

OfiTE 112-00, Instruction Manual, Page: 5 / 16

Share
Download
OfiTE 112-00 Instruction Manual Download Page 5

Control

Panel

The instrument control panel consists of a display screen, a Scroll Wheel,
and an Exit button.

The Scroll Wheel spins clockwise and counter-clockwise.  Spinning the
wheel scrolls through the menu and options.  Pushing the Scroll Wheel in
signals acceptance.

The Exit button cancels any pending input and returns to the Main Menu.
Pushing the Exit button while on the Main Menu accesses the Zero Menu.

To access the 

Main Menu, 

push in the Scroll Wheel while on the home

screen.  On the Main Menu you can set the motor speed to one of 5 preset
values:

1. Set RPM to 0
2. Set RPM to 60
3. Set RPM to 200
4. Set RPM to 600
5. Set RPM to 1000

To access the 

Manual Speed Select

, spin the Scroll Wheel while on the

home screen.  From here you can increase the motor speed by spinning
the wheel clockwise and decrease it by spinning it counter-clockwise.

By default, the speed increases by 1 RPM for each increment of wheel
spin.  By pressing the wheel in, you can increase this increment to 10 or
100 RPM.  

SPIN: ADJUST RPM
ENTER: ADJUST RPM BY 1, 10, 100

To access the 

Zero Menu

, press the Exit button while on the home screen.

From here you can set the test time and torque values to zero.

1. Zero the Test Time
2. Set Torque = 0.0
3. Restore Last Torque

To stop the motor, press the Scroll Wheel in twice.

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

4

Summary of Contents for 112-00

















Reviews:

No comments