manualshive.com logo in svg

OfiTE 112-00, Instruction Manual, Page: 12 / 16

Share
Download
OfiTE 112-00 Instruction Manual Download Page 12

a. Remove the belt guard.

b. Remove the gear from the main shaft.

c. Unscrew the four screws beneath the gear and remove the plate to

reveal the bearing.

d. Press the bearing upward from underneath and slide it up and off

the main shaft.

e. Slide the new bearing down the main shaft and into place.

f.

Re-install the plate and secure it tightly in place.

g. Re-install the gear, belt, and belt guard.  Check the belt tension as

described below.

3. Keep the control panel clean and dry.  Fluids on the panel can seep

around electrical components and cause damage.

4. Periodically remove the belt guard and check the belt tension. Ensure

sufficient tightness so that when the motor is stalled, the belt will not
slip.  To increase the belt tension, loosen the motor mount bolts on the
back of the unit, slid the motor towards the torque adjust handle and
then retighten the mounting bolts.  Re-install the belt guard.

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

11

Summary of Contents for 112-00

















Reviews:

No comments