manualshive.com logo in svg

OfiTE 112-00, Instruction Manual, Page: 2 / 16

Share
Download
OfiTE 112-00 Instruction Manual Download Page 2

Table of

Contents

Introduction..........................................................................................2

Description ...........................................................................................2

Specifications ......................................................................................2

Components.........................................................................................3

Control Panel .......................................................................................4

Lubricity Test .......................................................................................5

EP Test..................................................................................................8

Reporting Test Results.....................................................................9

Disassembly.......................................................................................10

Maintenance .......................................................................................10

Standardizing the Test Block .........................................................12

Block Adjustment ...........................................................................13

Measurements / Calculations...........................................................14

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

1

Summary of Contents for 112-00

















Reviews:

No comments