background image

 

 
Before opening the machine in case of malfunction or emergency, switch off by 
means of the ON/OFF switch and disconnect it from electric power source.

 

 
Electric power can cause severe injuries. All symptoms of faulty electric components 
to be taken seriously and possible causes for accidents to be eliminated immediately. 
All repair work only to be carried out by qualified service personnel. 
 
Make sure that the machine cannot move. If the machine is equipped with a brake, it 
must be set during working. 
 
Repair work in the high pressure section of the machine (pump, hoses, piping) only to 
be carried out by qualified personnel. 
 
Exhaust gas piping is getting hot during operation. Do not touch! 
 
During loading hoisting device to be fastened properly at jack rings. Ensure balanced 
load distribution. 
 
After work the machine to be locked and secured against unauthorized/accidental 
operation by means of the safety lever. 
 
For immission control purposes oil heated high pressure cleaners to pass a yearly 
immission value test, results of which to be recorded. 

 

Use of equipment and/or consumables which is not delivered or expressively 
approved by OERTZEN results in expiry of the EC Declaration of Conformity, as 
well as product liability and warranty.

 

 

 

Summary of Contents for Compact 120 K



















Reviews: