background image

 

4.

 Start-up/Shut-down 

 

Before Start-up 

 
Read operation manual and follow instructions. 
 
Upon start-up of the high pressure cleaner indoors, proper ventilation 
and exhaust evacuation to be guaranteed. Relevant safety regulations to 
be followed.  
 

In order to guarantee proper condition of the machine and trouble-free 
operation, carry out the following checks before start-up: 

  General condition of the unit (connections, seals, etc.) 

 Power 

cables/connections 

  Check all hoses for damage 

  Air supply to be ensured 

  Fill in all consumables required 

  Check correct oil level of high pressure pump (dip stick), only oil qualities 

approved by OERTZEN to be used (OERTZEN OSP special pump oil).  

  Check high pressure pump/pump connections for leaks 

  Machine only to be run with absolutely clean water. Thoroughly flush water 

supply hose before connection. Depending on water quality, filter to be 
checked in regular short intervals and replaced whenever needed. 

  Machine to be run horizontally (+/- 5°) 

 
In order to guarantee proper condition of the machine and trouble-free 
operation, carry out the following checks during operation: 

  Observe control indications/devices whether functioning 

  Observe pressure whether varying 

  Observe high pressure pump, hoses, connections whether leaking 

  Observe abnormal noise 

 

In case of malfunctions switch off machine immediately, eliminate 
cause according to chapter "Trouble Shooting", call qualified 
service. 

 

Connections 

 
Water Connection 

Water inlet (6) of the unit to be connected to the water distribution network by 
means of an internally clean, min. 

” water hose (diameter: see table below). 

For connections to the potable water distribution network DIN 1988 to be 
considered (for short-time connection a back-flow preventer with non-return 
protection and ventilation to be used). 
 

Flow Pressure 

Flow Rate minimum * 

minimum:  2 bar 
maximum: 8 bar 

 15 l/min. 

"     supply hose 

 21 l/min. 1"      supply hose 

 30 l/min. 1 

"  supply hose 

* see Technical Data 

 

Water shortage may cause severe damages on the pump unit 
(cavitation). 

 

 

Summary of Contents for Compact 120 K



















Reviews: