Oertzen 311 C Operation Manual Download Page 15

Page: 15 / 16

Trouble

Shooting

Electrical energy can cause severe injuries. Electrical components tho-

roughly and frequently to be checked for damages and malfunctions, in
order to avoid any cause for accidents. Disconnect the unit from the
electrical network during all repair/maintenance work (ZH 1/95).

Trouble Shooting: - only to be carried out by qualified service personnel.

Malfunction

Cause

Remedy

Electr. motor does not start.

Motor protection switch pushed.Push motor protection switch.

Unit not connected to power

Insert plug into socket.

source

Fuse burnt.

Replace fuse. If fuse burns

again,

call

qualified

service.

Phase in electr. plug missing. Install phase acc. to electr.

wiring

diagram.

Motor protection switch faulty. Call qualified service.

Electr. motor suddenly stops.

Fuse burnt (phase missing).

Replace fuse.

fuse

burns

again

motor

noisy,

call

qualified

service.

Low voltage/thermal overload. Arrange required voltage

(refer

techn.

data,

name

plate).

Cool

down

motor,

re-start,

call

qualified

service.

Motor protection switch faulty. Call qualified service.

Operating pressure high.

Clean/replace nozzle (refer to

techn.

data).

Electr. motor is noisy at

Fuse burnt (phase missing).

Replace fuse.

start-up. If

fuse

burns

again,

call

qualified

service.

Fault in electr. network.

Check phases in electr. plug.

Operating pressure not

Air in unit.

Bleed HP-cleaner.

achieved,

varies. Open

pressure

adjusting

handle

and

pistol

unless

stable

pressure

achieved.

Water shortage.

Water supply hose too small
(see table).

Nozzle

worn.

Replace

nozzle.

Incorrect

nozzle

Install correct nozzle.

Nozzle partly clogged.

Dismantle and clean nozzle.

Water filter clogged.

Dismantle, clean and flush.

Vibrations on high pressure

Air in unit.

Open pressure adjusting

hose and pistol.

handle and pistol unless

stable

pressure

achieved.

Clean strainer.

No detgergent injection.

Detergent tank empty.

Re-fill tank.

Dosing valve a/o pressure

Open.

adjusting

handle

closed.

Low pressure nozzle in

Dismantle, clean.

double

lance

clogged.

Non-return valve blocked

Blow compressed air into

detergent hose

Summary of Contents for 311 C

















Search results

Summary of Contents for 311 C

Reviews:

Related manuals for 311 C

Brands by name

Popular brands

Oertzen 311 C, Operation Manual

Search results

Summary of Contents for 311 C

Reviews:

Related manuals for 311 C

Brands by name

Popular brands