background image

2

English

SAFETY AWARENESS

Whenever you see the symbols shown below, heed their 

instructions! Always follow safe operating and maintenance 

practices. 

 DANGER

DANGER indicates a hazardous situation which, if not 

avoided, will result in death or serious injury.

 WARNING

WARNING indicates a hazardous situation which, if not 

avoided, could result in death or serious injury.

 CAUTION

CAUTION indicates a hazardous situation which, if not 

avoided, could result in minor or moderate injury.

NOTICE

NOTICE is used to address practices not related to 

personal injury.

NOTE

 

This note symbol indicates points of particular interest for 

more efficient and convenient operation.

ENVIRONMENTAL PROTECTION

To help preserve the environment, properly discard used 

batteries, oils and fluids, or other engine components that you 

might dispose of in the future.  

Consult your authorized equipment dealer or local 

environmental waste agency for their proper disposal procedure. 

This also applies to disposal of the entire engine at the end of 

its life.

FOREWORD

Thank you for choosing this production. This Owner’s Manual 

is provided to aid you in the safe and reliable operation of your 

production. READ AND UNDERSTAND IT THOROUGHLY 

BEFORE OPERATING YOUR PRODUCTION.  

  

To ensure a long, trouble-free life for your production, give it 

proper care and maintenance in accordance with this Owner’s 

Manual.  

  

No part of this publication may be reproduced, stored in a 

retrieval system, or transmitted in any form or by any means, 

electronic mechanical photocopying, recording or otherwise.  

  

Although every possible care has been taken to make 

this manual as complete and accurate as possible, the 

manufacturers cannot guarantee against errors and omissions. 

Due to improvements in design and performance during 

production, procedures and specifications are subject to change 

without prior notice.  

  

Illustrations are provided for general reference purposes, and 

may differ from actual product aspects and components.

March 2015 (2)

TABLE OF CONTENTS

POWER UNIT DP-10 …………………………………………… 1

READ THIS FIRST ………………………………………… 1

TABLE OF CONTENTS …………………………………… 2

SAFETY AWARENESS …………………………………… 2

ENVIRONMENTAL PROTECTION ……………………… 2

FOREWORD ………………………………………………… 2

SPECIFICATIONS ………………………………………… 3

PREPARING FOR OPERATION/DP-10 …………………… 3

OPERATING INSTRUCTIONS …………………………… 6

CATALYTIC CONVERTER ………………………………… 7

MAINTENANCE AND ADJUSTMENT …………………… 8

TROUBLESHOOTING GUIDE …………………………… 10

STORAGE …………………………………………………… 10

ATTACHMENTS ………………………………………………… 11

1. Nylon Cutter CB-20 ………………………………………… 11

READ THIS FIRST ………………………………………… 11

SPECIFICATIONS ………………………………………… 12

ASSEMBLY AND PREPARATION ………………………… 12

OPERATING INSTRUCTION ……………………………… 13

MAINTENANCE AND ADJUSTMENT …………………… 15

2. Articulating Hedge Trimmer CH-20 …………………… 16

READ THIS FIRST ………………………………………… 16

SPECIFICATIONS ………………………………………… 16

ASSEMBLY AND PREPARATION ………………………… 17

OPERATING INSTRUCTIONS …………………………… 18

MAINTENANCE AND ADJUSTMENT …………………… 18

3. Pruner CP-10 ……………………………………………… 19

READ THIS FIRST ………………………………………… 19

SPECIFICATION …………………………………………… 19

OPERATING INSTRUCTIONS …………………………… 20

MAINTENANCE AND ADJUSTMENT …………………… 20

ASSEMBLY AND PREPARATION ………………………… 20

4. Extension CX-10 …………………………………………… 22

READ THIS FIRST ………………………………………… 22

SPECIFICATIONS ………………………………………… 22

ASSEMBLY AND PREPARATION ………………………… 22

Summary of Contents for DP-10

























Reviews: