background image

AIR  CONDITIONER  FEATURES

Before you begin, thoroughly familiarize yourself with the control panel and remote controller 

and all its functions, then follow the symbols for the functions you desire. 

The unit can be controlled by the unit control panel itself with the remote control. 

ELECTRONIC CONTROL OPERATING INSTRUCTIONS

Fig.4

 NOTE: This manual does not include Remote Controller Operations, see the <<Remote 

 Controller Instruction>> packed with the unit for details. 

OPERATION PANEL OF THE AIR CONDITIONER

6

2

3

4

7

8

1

Selects the operating mode. Each time

 you press the button, the mode cycles through

the following sequence: AUTO, COOL, DRY,

 FAN and HEAT(not available on cooling only 

T

models). he mode indicator light illuminates

according to the mode selected.  Fig.4.)

(

MODE select button

1

         Used to adjust (increasing/decreasing) 

         temperature settings(one degree increments)

         in a range of 17 C(62 F) to 30 C(88 F) or

 the TIMER setting.

  

 

          

          

      

        

6

 UP(     ) and DOWN(    ) button

    

   

NOTE:

 The control is capable of displaying 

    temperature in Fahrenheit or  Celsius. 

To convert from one to the other, press  and

 hold the Up and Down buttons at the same 

  time, for 3 seconds.

3

Used to initiate the AUTO ON start time and

AUTO OFF stop time program, in conjuction

with the      &      buttons.

TIMER button

4

Used to initiate the SLEEP mode.

SLEEP button

6

2

         Power switch on/off.

POWER button

AUTO

HEAT

COOL

DRY

FAN

MODE

ION

SLEEP

FAN

TIMER ON

TIMER OFF

F

C

5

FAN button

7

O

 Shows the set temperature in    C  or

O

      F  and the Auto-timer settings.  

While on DRY and FAN modes, it  shows 

the room temperature.

 

LED Display

SWING

Remote signal receptor

(Some models have the 

  signal receptor on the 

  front panel , Fig.2)

9

(Only available on 

  models with auto-

  swing feature)

Controls the fan speed. Press to select the fan

speed in four steps-LOW, MED, HI and AUTO.

The fan speed indicator light illuminates the 

corresponding fan settings except AUTO .  On

 AUTO fan speed, all  fan indicator lights will be off.

Error codes and protection code:
E1-  

Room temperature sensor error- 

        Unplug the unit and plug it back in. 

        If error repeats, call for service.

E2-  

Evaporator temperature sensor error- 

        Unplug the unit and plug it back in. 

        If error repeats, call for service.

E4-  

Display panel

 

communication

 error- 

        Unplug the unit and plug it back in. 

        If error repeats, call for service.

P1-  

Bottom  tray is full

 

- Connect the 

        drain hose and empty the collected 

        water.  If error repeats, call   for service.

5

HI

MED

LOW

5

Summary of Contents for OBZ-08PE



















Reviews: