background image

INSTALLATION  INSTRUCTIONS 

INSTALLATION INSTRUCTIONS

Placement

Window Slider kit Installation

     

Note:

 If the window opening is less than the recom-

 

    

 m

mended inimum length of the window slider kit,

make

    

 a hole to  fit the window opening. 

  

Never cut the hole out of the window slider kit. 

Fig.7

bolt

Window slider kit

B

Horizontal 

window

Vertical

 

window

Window Slider Kit 

Minimum: 26.5 in. (2.22ft).

Maxmum:48.4 in.

26.5 in.

48.4 in.

(4.04ft).

Fig.9a

Fig.8

Fig.9

The air conditioner should be placed on a firm 

foundation to minimize noise and vibration. For 

safe and secure placement , place the unit on a 

smooth, level floor. 
The unit has casters for easy mobility, but it should

only be rolled on smooth, flat surfaces. Use caution 

when rolling on carpet surfaces. Do not attempt to 

roll the unit over objects.
The unit must be placed within reach of a properly 

 grounded socket.

Never place any obstacles around the air inlet or 

outlet of the unit.
Allow 1 ft. to 3.3 ft. of space from the wall to the

 

window for efficient air-conditioning. (see Fig.7).

     Your window slider kit has been designed to fit most 

     standard   vertical and  horizontal window 

     applications,  However, it may be necessary for you to 

     improvise/modify some aspects of the installation 

     procedures for certain types of window. Please refer 

     to Fig. 8 & Fig.9 for minimum and maximum window 

     openings.Window slider kit can be fixed  with a bolt

     (see Fig.9a).

A:1-3 ft

A

B: 1 ft

Window Slider Kit 

Minimum:

(2.22ft).

Maxmum:

(4.04ft).

8

Summary of Contents for OBZ-08PE



















Reviews: