background image

 

 V SERIES V310 | V390 | V480 VARIABLE 3 SPEED POOL & SPA PUMP 

 INSTALLATION AND OPERATION MANUAL

 

 

[email protected] 
oasisaquatics.com.au 

6

 

 

PIPE CONNECTION 

A barrel union is provided for connecting to the piping from the pool. 

The pumps are designed to accept the following PVC Pipes: 

 

Inlet PVC Position 40mm pipe ID or 50mm fitting ID PVC pressure pipe fittings 

 

Outlet PVC Position 40mm pipe ID or 50mm fitting ID PVC pressure pipe fittings 

 

The use of pipe with a  smaller ID than those specified above is not recommended and may cause 
damage to the pump voiding warranty. 

A straight length of pipe measuring no less than 300mm should be installed in front of the inlet of 
the pump allowing quieter and smoother operation. 

Suction  piping  should  be  free  from  all  air  leaks  and  any  humps  and  hollows,  which  may  cause 
suction difficulties. 

The outlet piping from the pump should be connected to the inlet connection on the swimming pool 
filter (at the filter valve). 

For pump installations above water level, it generally requires a check valve in the suction line. 

Do  not  use  type  ‘P’  (green)  plumber’s  glue  on  the  barrel  unions  as  this  may  cause  damage  to  the 

material used. 

Always install pump for maintenance and service accessibility. 

 

USAGE WARNING 

 

 

The V SERIES is manufactured wit

h technological advances including PCB’s and microchips.  It 

is necessary to turn power off completely for 10 seconds prior to turning pump back on again 

 

Some  brands  of  older  style  chlorinators  may  release  a  small  amount  of  power  to  the    even 

whilst  it  seems  turned  off.    It  this  occurs  the  PUMP  may  not  reset  correctly  until  power  is 
completely disconnected. 

 

In some cases, chlorinator manufacturers may be able to modify internal components so as to 
work in with the V310. If not a suitable chlorinator may be required. 

 

Oasis

’s 

CX  chlorinator  completely  disconnects  power  to  the  pump  when  the  pump  is  in  off 

mode. 

Summary of Contents for V Series

















Reviews: