- 9 -
POWER LINE
terminals 1-2
Connect to a 230 Vac ± 10%, 50 Hz, single-phase power source.
Connect NEUTRAL to terminal 1. Connect POSITIVE to terminal 2.
Connect EARTH to the internal earth terminal on the body of the unit.
We advise the installation of a 10A thermal cut-out switch upstream.
The controller is protected by a high-speed 160 mA fuse (F1-TRS).
MOTOR
connector J4
Supplied already wired and tested together with the 10
μ
F 450Vac condenser.
Protection against overcurrents by means of quick 4 A fuse (F3 - ENG).
Regulation of working time (WORK TRIMMER) to protect the motor in the event of travel stop fault.
Dip-switch 7 makes it possible to invert the direction, which facilitates mounting the motor in any position.
TRAVEL STOPS
connector J5
Supplied already fitted and tested (FCA on terminals 20-22 ; FCC on terminals 21-22 ).
Check: with gate open, FCA LED off and FCC LED on; with gate closed, FCC LED off and FCA LED on.
PUSHBUTTON PANEL
terminals 7-8-9-10; 7-8-43
Accessories.
The PT3/S pushbutton panel (Start, Stop, Indicator light) or the PT2/S pedestrian panel (Start,Stop) is used.
Connect the Start button to terminals 8-9 (N.O. contact) for complete opening/closing or to terminals 8-43
(N.O. contact) for partial opening. Check that the related command lights up the RUN or PAR LED, respectively.
Connect the Stop button to terminals 7-8 (N.O. contact) and the 24 Vac- 3W light to terminals 8-10.
The function indicator light flashes rapidly when the gate is closing; it remains off when the gate is closed.
The light flashes slowly when the gate is opening, and when the gate is open, the light is on.
A similar indication is given by the LGT LED situated on the controller.
N.B.:
If the Stop button is not connected, the controller is not enabled. In this case, short circuit
terminals 7-8 and check that the STP LED is normally lit.
KEYED SWITCH UNIT
terminals 7-8-9-43
Accessory: keyed switch unit model SCZ.
Connect the N.O. contact of the unit to terminals 8-9 for complete opening or to terminals 8-43 for pedestrian opening.
Connect the N.C. contact to terminals 7-8 to obtain the Stop function.
MAGNETIC KEY READER
terminals 8-9-43
Accessory: reader model SCK.
Use the related N.O. contact to obtain the Start function (terminals 8-9) or pedestrian Start (terminals 8-43)
If only the reader is used, and not the pushbutton panel, short circuit terminals 7-8.
MAGNETIC DETECTOR
terminals 7-8; 8-9; 18-19
Accessory: magnetic detector model RM416-8 can be used as a Start, Stop or security control.
To use as a Start control, connect N.O. to terminals 9 and 8.
To use as a Stop control, connect N.C. to terminals 8 and 7.
To use as a Security control, connect N.C. to terminals 18 and 19.
Check: the presence of a metallic body on the coil turn should cause the RUN LED to light up and the
STP or LUX LED to go off.
PHOTOCELL
terminals 14-15-18-19
Accessory.
Connect terminals 1-2 of transmitter TX to terminals 14-15 of the controller.
Connect terminals 1-2 of receiver RX (24 Vac) to terminals 14-15 of the controller.
Terminals 14-15 supply a 24Vac utility protected by a 500 mA fuse (F4-24V).
Connect terminals 4-5 of the receiver to terminals 18-19 of the controller.
Check: with photocell interrupted, LUX LED is off. Select the programme desired using dip-switch 5.
F
LASHER
terminals 11-12
Accessory: flasher model SLR shows
that the system is operating.
Connect terminals 11 and 12, following the numbering.
When dip-switch 4 in positioned to ON, the flasher begins operating 2.5 sec. before each phase of movement.
The output is protected by a special 250 mA fuse (F2-SLR) : only use 230Vac lamps of max. 40W.
CONNECTION INSTRUCTIONS
