NXP Semiconductors OM13260 Installation Manual Download Page 16 | Manualshive

Page: 16 / 71

NXP Semiconductors OM13260 Installation Manual Download Page 16

NXP Semiconductors

UMxxxxx

Install Guide

All information provided in this document is subject to legal disclaimers.

Preliminary 1

— September 6, 2013

© NXP B.V. 2013. All rights reserved.

16 of 70

This completes the installation of the required driver. Check again with the Device Manager entry, which
should match figure 4.11.

Note: The actual COM port number is not important, and will vary depending upon other port assignments
in use on any particular machine.

4.7

Fm+ Development Board (OM13260) Firmware

Depending upon the intended operation of the Fm+ Development Board (OM113260) one of two
different firmware programs must be installed. These are summarized in Table 4.2.

Table 4.2 Supplied Firmware

FM+DevelopmentBoard V03_00.bin

19kb

Standalone_trade__DEMO.bin

7kb

When operated with the NXP GUI the Fm+ Development Board (OM13260) requires a different
firmware to that used for the “Trade Show” Mode (described in section 4.1). Repeat the steps given in
section 4.7 to install the GUI Firmware on to the Fm+ Development Board (OM13260) MCU.

4.7.1 “Trade Show” Mode

A popular use of the Fm+ Development Board (OM13260) kit is for publicity and promotion of the I2C
Bus products from NXP. A version of the firmware provides “Blinky Lights” on the Fm+ Development
Board (OM13260) PCB, and the optional attached GPIO Target Boards OM13303.

Note

:

This mode does not require a computer connection.

The NXP GUI will not work while the

firmware on the Fm+ Development Board (OM13260) is set to “Trade Show” mode.

Note:

To restore operation with the NXP GUI

running on a computer attached by USB cable, the

firmware on the Fm+ Development Board (OM13260) must be reset from “Trade Show” mode by
installing the correct firmware. (See section 4.8).

Once this is installed the Fm+ Development Board (OM13260)

will no longer work with the NXP GUI

(running on an attached PC). Each time the Fm+ Development Board (OM13260) is powered up the
demo program will run. No USB connection or computer is required, except for an external DC power
supply.

4.7.2 NXP GUI Mode

When the Fm+ Development Board (OM13260) is used with the NXP GUI the correct firmware must be
installed on the MCU. (See section 4.8).

Note:

This mode does require a computer connection.

The NXP GUI will only work when the

«
...
14
15
16
17
18
...
»

Summary of Contents for OM13260








































































Reviews:

No comments