EN
EN
Removing the Brake
Configuration
Remove the rear wheel per
Section 3
.
Removing Roller Brake Hardware
f
Remove left hand axle nut
(1)
, left
hand no-tur
n washer
(2)
, and left
hand nut
(3)
.
f
Secure the wheel and use
Nu-
Vinci
ser
vice tool
N360-BKAD-01
to remove the brake lock ring
(6)
, and remove the roller brake
adapter
(7
) from the hub.
Removing Rim Brake Hardware
f
Remove left hand axle nut
(1)
, left
hand no-tur
n washer
(2)
, left hand
nut
(3)
, and cupped washer
(4)
.
f
Using a thin flat device, pr
y and
remove the rim brake cover
(5)
.
Removing Disc Brake Hardware
f
Remove left hand axle nut
(1)
, left
hand no-tur
n washer
(2)
, left hand
nut
(3)
, and cupped washer
(4)
.
f
Secure the wheel and use
NuVinci
tool
N360-BKAD-01
to
remove the brake lock ring
(6)
,
and remove both the brake shield
(8)
and disc brake adapter
(9)
from the hub.
Installing the Brake
Configuration
Installing Roller Brake Hardware
f
Install the roller brake adapter
(7)
and apply a high strength thread
locking compound (equivalent
to Loctite® 277™) around one
complete thread of the brake lock
ring
(6)
.
f
Using
NuVinci
ser
vice tool
N360-
BKAD-01
, install and torque the
brake lock ring
(6)
to 55-65 Nm
(41-48 ft-lbs).
f
After installing roller brake, install
and torque left hand nut
(3)
to
30-35 Nm (22-26 ft-lbs).
Installing
Rim Brake Hardware
f
Press rim brake cover
(5)
into po-
sition until it seats fully
, followed
by the cupped washer
(4)
.
f
Install and torque left hand nut
(3)
to 30-35 Nm (22-26 ft-lbs).
Installing
Disc Brake Hardware
f
Install the disc brake adapter
(9)
and brake shield
(8)
and applya
high strength thread locking
compound (equivalent to Loctite®
277™) around one complete
thread of the brake lock ring
(6)
.
f
Using
NuVinci
tool
N360-
BKAD-01
, install and torque the
brake lock ring
(6)
to 55-65 Nm
(41-48 ft-lbs).
f
Install and torque left hand nut
(3)
to 30-35 Nm (22-26 ft-lbs).
5. SERVICE INSTRUCTIONS
19
20
N360 Specifications
Hub Colors
Silver or Black
Spoke Configurations
32 or 36 Hole
Brake Configurations
Disc, Rim or Roller
Speed Ratio
Infinitely V
ariable
within Ratio Range
Ratio Range
360% Nominal
(0.5 Underdrive to
1.8
Overdrive)
Shifting
V
ariable T
wist Grip,
3/4
Turn
Drop
-Out Width
135 mm, Horizontal
or
V
ertical
Axle L
ength
183 mm
Axle Threads
M10x1
Chainline
49.0 ± 0.5 mm
Beltline
45.5 ± 0.5 mm
Sprockets
16-22 T
ooth Supported
(standard 9-
spline, not included)
Sprocket Ratio
1.8:1 Minimum
(16/29, 17/31, 18/33, 19/35, 20/36,
21/38, 22/40,
larger front chainrings
can be used without exception)
Spoke Flange Diameter
125.0 mm
Center to L
eft Spoke Flange
26.0
mm
Center to Right Spoke Flange
26.0
mm
For the most up-to-date
NuVinci
N360 CVP Owner and T
echnical
Manuals please visit us online at
www
.nuvinci.com/suppor
t
6. TECHNICAL DA
TA
f
Reference Exploded Diagram P
.21
f
Reference Exploded Diagram P
.21
