background image

 

MANUFACTURER :  

 

NÜVE SANAYİ MALZEMELERİ                                
İMALAT VE TİCARET A.Ş. 

 

 

         

Saracalar Mah

. Saracalar Kümeevleri No: 4/2  

Akyurt 06750 Ankara-TURKEY 

 

 

TEL:  +(90)  312 399 28 30 (pbx)   

 

 

 

FAX:  +(90) 312 399 21 97   

 

 

 

 

E-mail: [email protected]   

 

 

 

 

 

 

 

 

 

 

 

              

 

 

WARRANTY CERTIFICATE 

 
1. 

Nüve  warrants  that  the  equipment  delivered  is  free  from  defects  during  material  and 
workmanship.  This  warranty  is  provided  for  a  period  of  two  years.  The  warranty  period 
begins from the delivery date. 

 
2. 

Warranty  does  not  apply  to  parts  normally  consumed  during  operation  or  general 
maintenance  or  any  adjustments  described  in  the  operating  instructions  provided  with  the 
equipment. 

 

3. 

Nüve does not accept any liability in the case where the goods are not used in accordance 
with their proper intent. 

 

4. 

The warranty may not be claimed for damages occurred during the shipment, for damages 
resulting  from  improper  handling  or  use,  the  defects  in  maintenance,  negligence,  bad 
functioning  of  auxiliary  equipment,  in  the  case  of  force  majeure  or  accident  and  incorrect 
power supply. 

 

5. 

In the event of failure, Nüve shall be under no liability for any injury, or any loss or damage 
as the result of the failure other than the guarantee conditions. 

 

 

BEFORE  OPERATING  THE  INSTRUMENT  THIS  MANUAL  SHOULD  BE  READ 
CAREFULLY. 

 

 

THE  VALIDITY  OF  THE  GUARANTEE  IS  SUBJECT  TO  THE  OBSERVATION  OF  THE 
INSTRUCTIONS AND PRECAUTIONS DESCRIBED IN THIS MANUAL. 

 

 

INFORMATION CONTAINED IN THIS DOCUMENT IS THE PROPERTY OF NÜVE. IT MAY 
NOT BE DUPLICATED OR DISTRIBUTED WITHOUT PERMISSION. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for NF 048


















Reviews: