background image

Reference Table

 

 

Note: 

The  production  place,  storing  time,  baking  time  and  the  like  of  oil  plants  will  affect  the  oil 
extraction rate, so please select the highest quality oil plants for the extraction of oil when buying 
your plants/grains/nuts to obtain the best oil possible. 
 

Baking Method 

If users would like to bake peanuts and soybeans manually, please follow the instructions below to 
bake them in the right way. Choose “Other" for the Oil Plants selection and the “Raw” function; 
then, press the "Start" button. The machine will heat up in 6 minutes before extraction. 
 
The  best  oil  yield  from  peanuts  and  soybeans  can  be  obtained  through  suitable  baking.  If  the 
baking time is too short, there will be cases of not extracting a large amount of oil. 
 
On the contrary, if the baking time is too long, the oil extraction yield will be affected, so please 
read below contents carefully 
 

Baking method:

 Using microwave oven, roaster or pan. 

Baking time: Baking in small quantities is  the best method. For example, 500g of peanuts will 
require a baking time of roughly 4 minutes; soybeans will take about 10 minutes. (Baking time 
will differ because of the moisture content of oil plants). If baking quantity is big, make sure to stir 
them during the baking to get uniform baking. 
 
Three judgment standards are as follows: 
1) Bake until the aroma of the plant/grain/nut can be smelled. 
2) Bake to the degree that the plant/grain/nut can be eaten. 
3)  Bake  until  the  peanut  skin  can  be  taken  off  easily  by  hand  and/or  the  shell  of  the  soybean 
cracks. 
 
While squeezing peanuts, please play close attention to the waste outlet. Unsuitable baking times 
and  small  pieces  of  peanut  might  stick  to  the  feeding  channel  and  affect  normal  extraction.  If 
there's no waste coming out for 1 minute, open the cover, use the push rod or a chopstick to poke 
the feeding channel of the pan (using your hand is forbidden). 
Smaller nuts have relative low yield of oil and will easily get stuck in the feeding channel. Please 
use only big pieces of plants/grains/nuts. 
 

Oil plants

Peanut     Black sesame White

 

sesame

Rapeseed

Sunflower 

seed

Walnut

Oil extraction 

rate

35-48%

35-42%

40-48%

25-35%

40-50%

40-68%

Oil plants

Soybean

Flaxseed

Tea seed

Oil extraction 

rate

8-11%

25-34%

28-35%

Summary of Contents for PKOPR15

















Reviews: