NST HK-HDVR8-3 User Manual Download Page 99

Page: 99 / 168

Digital Video Recorder User Manual

Configure the port parameters of USB-to-RS-232 convertor, including the serial number of port, baud
rate, data bit, stop bit, parity and flow ctrl.

When using USB->RS-232 convertor mode, the port of USB-to-RS-232 convertor and the POS must be

corresponding to each other, e.g., POS1 must be connected to port1 of the convertor.

Figure 9. 4

USB-to-RS-232 Settings

RS-232 Connection

Connect the DVR and the POS machine via RS-232. The RS-232 settings can be configured in

Menu>Configuration>RS-232. The Usage must be set to Transparent Channel.

Multicast Connection

When connecting the DVR and the POS machine via Multicast protocol, set the multicast address and

port.

Figure 9. 5

Multicast Settings

Sniff Connection
Connect the DVR and the POS machine via Sniff. Configure the source address and destination address
settings.

Summary of Contents for HK-HDVR8-3









































































































































































Search results

Summary of Contents for HK-HDVR8-3

Reviews:

Related manuals for HK-HDVR8-3

Brands by name

Popular brands

NST HK-HDVR8-3, User Manual

Search results

Summary of Contents for HK-HDVR8-3

Reviews:

Related manuals for HK-HDVR8-3

Brands by name

Popular brands