background image

15

CODE

MEANING

SOLUTION

32

Solenoid weld-

ed. Caused by 

wiring short 

circuit in con-

tactor wiring or 

contactor coil. 

Internal control 

system check 

failure.

Check wiring and 

solenoids.  Turn 

keyswitch off and 

on.  Call for service if 

problem persists.

33

Solenoid did not 

close. Caused 

by wiring short 

circuit in con-

tactor wiring or 

contactor coil. 

Internal control 

system check 

failure

Check wiring and 

solenoids.  Turn 

keyswitch off and 

on.  Call for service if 

problem persists.

37

Throttle fault.  

Internal control 

system check 

failure.

Check joystick and 

wiring. Turn machine 

off and then on. If 

problem continues 

call for service

36

Right brake 

overcurrent

Call for service.

39

Left brake over

-

current

Call for service.

3A

Right brake 

circuit open

Turn on brake lever 

then turn machine off 

and then on. If prob

-

lem continues call for 

service.

40

Left brake cir

-

cuit open

Turn on brake lever 

then turn machine off 

and then on. If prob

-

lem continues call for 

service.

F42

The brush mo-

tor or a drive 

motor is ex-

ceeding the cur-

rent limit set in 

the controller.

Select lower pad 

pressure setting.  

Check brakes. Turn 

machine off and then 

on. If problem contin

-

ues call for service.

44, 4C, 

45, 59, 60

Caused by wir-

ing short circuit 

in drive wiring 

or shorted drive 

motor. Carbon 

brushes need 

service.

Check wiring and 

drive motor for short 

circuit. Correct prob-

lem if found.  Check 

carbon brushes. If 

problem continues 

call for service.

4D, 46, 61

Caused by wir-

ing short circuit 

in brush wir-

ing or shorted 

brush motor.  

Carbon brushes 

need service.

Check wiring and 

brush motor for short 

circuit. Check car

-

bon brushes. Correct 

problem if found. If 

problem continues 

call for service.

58

The deceleration 

of the brush 

motor or drive 

motor exceeded 

set parameters. 

Example: Tried 

to slow down 

or stop on too 

steep a hill.

Turn machine off and 

then on. If problem 

continues call for 

service.

CODE

MEANING

SOLUTION

62

Wired incor-

rectly. Internal 

control system 

failure.

Check wiring. Turn 

machine off and then 

on. If problem contin

-

ues call for service.

63

Caused by wir-

ing short circuit 

in contactor wir-

ing or contactor 

coil.

Check wiring and con

-

tactor for short cir-

cuit. Correct problem 

if found. If problem 

continues call for 

service.

Battery Charger Error Codes

Always confirm the battery charger settings match the 

batteries installed if an error code is displayed.

If any error codes are displayed:

•  Unplug the charger.

•  Check the battery connections are clean and tight.

•  Check the electrolyte level in each cell (flooded 

batteries only).

• 

Try charging again.  First charge on new batteries 

may result in a code.

Code

Meaning

E01

Max battery V reached.  Verify charger is set 

to match the installed batteries

E02

Charger maximum internal temperature 

reached.  Charge with Upper Body open, and 

Storage Compartment cover open.

E031 Phase 1 safety timer 18h reached.  Batteries 

need replaced.

EDI

Phase 1 battery voltage failed to rise. If 

batteries are new charge again, otherwise 

replace the batteries.

E032

Phase 2 safety timer 10hr reached.  If bat

-

teries are new, try charging again.  If batter

-

ies are >1yr old they need replaced

EDU

Phase 2 batteries require excessive current 

to hold voltage.  If batteries are new charge 

again, otherwise replace the batteries.

SCt

Overall Safety Timer.  Replace the batteries.

Srt

Charger internal short - replace the charger.

Summary of Contents for eForce 26





















































Reviews: