background image

Form No. 70951A  1/09

  

                        Clarke

®

                                                                     Printed in the U.S.A.

READ THIS BOOK

This book has important information for the use and safe operation of this machine.  Failure to read this
book prior to operating or attempting any service or maintenance procedure to your Clarke machine could
result in injury to you or to other personnel; damage to the machine or to other property could occur as
well.  You must have training in the operation of this machine before using it.  If your operator(s) cannot
read this manual, have it explained fully before attempting to operate this machine.

All directions given in this book are as seen from the operator’s position at the rear of the machine.

For new books write to:  Clarke

®

 

,  2100 Highway 265, Springdale,  Arkansas  72764.

24V Model

C28, C33

U.S. Patent No. 6,760,947; No. 6,105,192; No. 6,493,896 (Deluxe Machines); & Patent Pending

Operator's Manual

Manual del operador

Manuel de l’utilisateur

 English (2 - 23)

 Español (24 - 45)

 Français (46 - 67)

READ THIS BOOK

LEA ESTE MANUAL

LISEZ CE MANUEL

ES

EN

FR

Summary of Contents for Focus C28





















Reviews: