NRG Systems LOGR-S User Manual Download Page 8

Page: 8 / 73

NRG Product Manual

LOGR-S Data Logger

NRG_LOGR-S_Manual
Rev. 1.0

[email protected] | Page 8

5 November 2021

Data

LOGR data acquisition provides for:

•

1 Hz sampling rate

•

Statistical data, processed at 1-minute intervals

•

Data storage via internal 8 GB microSD card

•

FTP Client

Communications

•

Ethernet port to access built-in webserver and Modbus data retrieval

Concept of Operation

LOGR requires network infrastructure support to operate as a sensor-to-SCADA interface:

•

Modbus Client (SCADA system to poll LOGR)

•

Web Browser (for configuration of LOGR, e.g., Google Chrome)

Optionally, the LOGR utilizes:

•

Local FTP Server (LOGR will deposit data/diagnostic/event log files if needed for backup
purposes)

•

Local FTP Client (for Administration of LOGR, such downloading/uploading unit or sensor
configurations)

•

Local NTP Server (LOGR will time synchronize once daily if a local NTP server is provided)

Summary of Contents for LOGR-S










































































Search results

Summary of Contents for LOGR-S

Reviews:

Related manuals for LOGR-S

Brands by name

Popular brands

NRG Systems LOGR-S, User Manual

Search results

Summary of Contents for LOGR-S

Reviews:

Related manuals for LOGR-S

Brands by name

Popular brands