background image

NOVUS AUTOMATION 

1/11 

 

 

 

TagTemp-S 

TEMPERATURE DATA LOGGER - INSTRUCTION MANUAL V1.0x 

1

 

INTRODUCTION 

TagTemp-S is an electronic temperature recorder. The temperature 

measured by the sensor is recorded in equipment internal memory. 

This data is transferred through a smartphone equipped with an 

embedded NFC interface or by an NFC interface connected to a 

computer through an USB port (both not included). 
LogChart-NFC application for ANDROID™ and the Nx Software for 

Windows® are the tools used to configure the operating mode, 

transfer and display data. The acquisition start and end parameters, 

logging interval, setpoint alarms and other parameters can be easily 

defined using these applications. 
The operating manual and Nx Software can be downloaded from 

the manufacturer's website. The ANDROID™ LogChart-NFC app 

can be downloaded from Google Play Store

2

 

MECHANICAL INSTALLATION 

TagTemp-S can be installed using a double-sided adhesive tape on 

the back of the device, taking care not to stick it over the 

identification tag. Another way is to use the blister hole to attach the 

transmitter. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

3

 

TECHNICAL FEATURES 

Operating 

temperature 

-30 °C to 60 °C 

Storage 

temperature 

From -30 °C to 65 °C. 

Measuring range 

Temperature: -30.0 °C to +60.0 °C. 

Accuracy of 

measurement 

±1 °C max. over the full measuring range. 
Note:  You can correct the measurement 

error in the OFFSET parameter using the 

configuration software. 

Measurement 

resolution 

Temperature: 0.1 °C / 0.1 °F 

Memory Capacity 

4020 registers. 

Interval between 

Measurements 

1 minute min. 
4 hours max. (240 minutes).  

Power Supply 

3.0 V lithium battery (CR2032), built-in, 

non-replaceable

Battery life 

(estimated) 

Above 2 years at a 5-minute acquisition 

interval. 

Dimensions 

37 x 57 x 8 mm 

RF Interface 

ISO 15693 (NFC-V) compatible. 

Data transfer time 

between register 

and smartphone 

Approx.  20 seconds (depends on the 

smartphone processing speed). 

LogChart-NFC 

Application 

ANDROID™ version: 4.0 or above. 
Languages: Portuguese or English. 

NFC interface for 

the computer 

USB  to NFC interface (optional), 

compatible with  Nx Software  for 

Windows®

Case 

Polyvinyl Chloride (PVC) 

Degree of protection  All electronics are protected by the 

housing. IP65 compatible. 

Certification 

CE 

Summary of Contents for 8813800000












Reviews: