NovoCon
T75 DES
Content
• General information
- Safety
- Symbolerklärung
- Work safety
- Dangers posed by the product
- Safety-relevant regulations
- Spares
- Changes to the product/ retrofitting
- Type plate
- Packaging
- Technical data
• Installation
• Programming the control
• Programming overview
• Operating instructions/
Function description
• Warranty terms
• Fault diagnosis
General information
·
Safety
It is important for the safety of persons to observe
these instructions. These instructions must be kept
safe. Comply with all instructions, since incorrect in-
stallation may result in severe injuries.
Before commencing any work on the product, read
the operating instructions in their entirety, especially
the chapter on safety and the relevant safety
instructions. The content of what you read must have
been understood. This product may pose a danger if
it is not used properly or contrary to its intended
purpose.
Intended use: see installation declaration.
The manufacturer's liability will be forfeited in cases
of damage which have been caused as a result of
disregarding these instructions.
To be installed by duly qualified and skilled personnel
only.
•
Definition of symbols
.
WARNING: Imminent danger
This symbol marks instructions that may
cause severe injuries if disregarded.
WARNING: Danger caused by
.
electric current
The relevant work must only be carried out
by a suitably qualified electrician.
This symbol marks instructions, that
may
!
cause malfunctions and/or the failure
of the drive, if disregarded.
Reference to text and image
• Work safety
Personal injuries and property damage can be
avoided while working with and on the product by
observing the safety and other instructions given in
this operating manual.
Any claims for damages and liability claims against
the manufacturer or his representative shall be
forfeited, if the safety and other instructions given in
this operating manual as well as the accident
prevention regulations and the general safety
regulations are disregarded.
• Hazards that may emanate from the product
The product has been subjected to a risk
assessment. The design and execution of the
product based on this corresponds to state-of-the-art
technology.
When used properly as intended, the product is safe
and reliable to operate.
Nevertheless, a residual risk will always remain!
The product runs on a high electrical voltage.
Before commencing any work on
electrical systems, please
observe the following:
1. Disconnect from the power supply.
2. Safeguard to prevent a power restart.
3. Check that the electricity supply is cut off.
4. Even non-running motors can pose a risk.
• Safety-relevant regulations
When installing, commissioning, maintaining and
checking the control, the local protection provisions
must be complied with.
0
The following regulations will have to be
observed:
- DIN EN 12445
Industrial, commercial and garage doors & gates -
Safety in use of power operated doors
—
Test
methods
- DIN EN 12453
Industrial, commercial and garage doors & gates -
Safety in use of powered operated doors
—
Requirements
- DIN EN 12978
Safety devices for power operated doors and gates
- Requirements and test methods
In addition to that, the normative references to the
following standards must be observed:
VDE-regulations
- DIN EN 418
Safety of machinery. Emergency stop equipment,
functional aspects. Principles for design
- DIN EN 60204-1/VDE 0113-1
Electrical systems with electrical equipment
- DIN EN 60335-1/VDE 0700-1
Safety of household and similar electrical appliances
• Spare parts
Only use genuine spare parts of the manufacturer.
Wrong or faulty spare parts can cause
damage, malfunctions or even a total failure
of the product.
•
Changes and modifications to the product
In order to prevent hazards and ensure
optimum performance, no changes,
modifications or conversions may be made
to the product that have not been expressly
approved by the manufacturer.
• Type plate
The type plate is affixed to the side of the control
housing. The connection values must be observed.
• Packaging
Always dispose of the packaging in an environmen-
tally-friendly way and in accordance with the local
disposal regulations.
Technical Data
Control
NovoCon T75 DES
Housing dimensions
Height x width x depth 250mm x 215mm x 120mm
Montage senkrecht
Cable glands
2 x M20
1 x M16
1 x M20 V-cut
Supply Voltage
3 x 400 V AC / 50 Hz
3 x 230 V AC / 50 Hz
1 x 230 V AC / 50 Hz
Control voltage
24 V DC
Max. motor output
6
approx. 0. kW at 230 V AC
1 1
40
approx. . kW at
0 V AC
Degree of protection
IP 54
Operating temperature
+ 50°C
-20°C
Manufacturer:
Novoferm tormatic GmbH
Eisenhüttenweg 6
D-44145 Dortmund
www.tormatic.de
Keep these installation, operating and maintenance instructions during the product's entire service life!
GB
WN 906006-57-6-50 07/17