background image

27

Document 51996 AFP-300/400 NION  Installation Rev. A1  03/04/03

3. Check the 

Backup screen database

 option if you wish to create a backup copy of the old screen

database file.  The backup will be saved as “screen.bak” and will be located in the same directory where
the utility was run.  This directory will normally be c:UniNet\PlugIns\screen.bak.
Select the name of the site you wish to convert by choosing from the drop-down list.
In the 

Select node to convert

 list, only NION-232 PCB board 300/400 nodes will be displayed as

options for upgrading.  In addition, any 300/400 nodes that have previously been converted will not be
displayed in this list.
Once you have selected the desired 300/400 node, specify the 

Panel Node Number

.  This is the

network node number programmed in the fire panel.

Figure A-3:  Performing the Conversion Upgrade

Once these parameters have been defined, click on 

Next 

to continue with the upgrade.  The utility will prompt you

to verify the information entered.  Once this is done, the utility will finish the upgrade process, and a message
saying “Upgrade complete” will be displayed.

IMPOR

IMPOR

IMPOR

IMPOR

IMPORTTTTTANT

ANT

ANT

ANT

ANT:  It is imperative that the correct panel node number be

:  It is imperative that the correct panel node number be

:  It is imperative that the correct panel node number be

:  It is imperative that the correct panel node number be

:  It is imperative that the correct panel node number be

entered during the conversion process.  F

entered during the conversion process.  F

entered during the conversion process.  F

entered during the conversion process.  F

entered during the conversion process.  Failure to do so will result in

ailure to do so will result in

ailure to do so will result in

ailure to do so will result in

ailure to do so will result in

device ID errors in the converted database.

device ID errors in the converted database.

device ID errors in the converted database.

device ID errors in the converted database.

device ID errors in the converted database.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for UniNet 2000 AFP-300 NION

































Reviews: