manualshive.com logo in svg

Nortel Media Dependent Adapters 302403-G, Installation Manual

Share
Download
Nortel Media Dependent Adapters 302403-G Installation Manual Download Page 9

 

7

Table 2

 describes the 400-4TX and 8100-4TX MDA front-panel.

Table 2   

400-4TX and 8100-4TX MDA front panel 

Item

Label

Description

1

100

100BASE-TX port status LEDs (green):

On: The corresponding port is set to operate at 
100 Mb/s. 

Off: The link connection is bad or there is no 
connection to this port.

Blinking: The corresponding port is management 
disabled.

2

10

10BASE-T port status LEDs (green):

On: The corresponding port is set to operate at 
10 Mb/s.

Off: The link connection is bad or there is no 
connection to this port.

Blinking: The corresponding port is management 
disabled.

3

F Dx

Full-duplex port status LEDs (green):

On: The corresponding port is in full-duplex mode. 

Off: The corresponding port is in half-duplex 
mode.

4

Activity

Port activity LEDs (green):

Blinking: Indicates the network activity level for the 
corresponding port. A high level of network activity 
can cause LEDs to appear to be on continuously.

5

10BASE-T/100BASE-TX RJ-45 (8-pin modular) port 
connectors.

Summary of Contents for Media Dependent Adapters 302403-G

































Reviews:

No comments

Brands by name

Popular brands

Load more brands