manualshive.com logo in svg

Nortel Media Dependent Adapters 302403-G, Installation Manual

Share
Download
Nortel Media Dependent Adapters 302403-G Installation Manual Download Page 11

 

9

100BASE-FX MDAs

The 100BASE-FX MDAs conform to the IEEE 802.3u 
100BASE-FX standard and can attach fiber-based 100 Mb/s 
connections to Fast Ethernet devices. The 100BASE-FX MDAs 
do not support single-mode fiber cable. The following are the

 

100BASE-FX 

MDAs.

•

400-2FX MDA (dual-port), 

page 10

•

400-4FX MDA (quad-port), 

page 13

•

8100-2FX MDA (dual-port), 

page 10

•

8100-4FX MDA (quad-port), 

page 13

•

BPS2000-2FX MDA (dual-port), 

page 12

•

BPS2000-4FX MDA (quad-port), 

page 15

For a complete list of MDAs, see 

Table 1 on page 4

. For 

installation instructions, see 

“Installing an MDA” on page 24

.

Dual-port 100BASE-FX MDAs

The dual-port 100BASE-FX MDAs use two longwave 1300 nm 
SC connectors to attach devices over 62.5/125 micron multimode 
fiber optic cable.

Off: No traffic to this port.

3

10BASE-T/100BASE-TX RJ-45
(8-pin modular) port connectors.

Table 3   BPS2000-4TX MDA description (continued)

Item

Label

Description

Summary of Contents for Media Dependent Adapters 302403-G

































Reviews:

No comments

Brands by name

Popular brands

Load more brands