manualshive.com logo in svg

Nortel Media Dependent Adapters 302403-G, Installation Manual

Share
Download
Nortel Media Dependent Adapters 302403-G Installation Manual Download Page 7

 

5

•

“GBIC MDA” on page 22

10BASE-T/100BASE-TX MDAs

The 10BASE-T/100BASE-TX MDAs use four RJ-45 (8-pin 
modular) connectors, configured as media dependent interface-
crossover (MDI-X) connectors. These ports connect over straight 
cables to the network interface controller (NIC) card in a node or 
server, similar to a conventional Ethernet repeater hub.

If you connect to another Ethernet hub or Ethernet switch, you 
need a crossover cable unless an MDI connection exists on the 
associated port of the attached device.

The following are the 10BASE-T/100BASE-TX MDAs. 

•

400-4TX MDA, 

page 6

•

8100-4TX MDA, 

page 6

•

BPS2000-4TX MDA, 

page 8

For a complete list of MDAs, see 

Table 1 on page 4

. For 

installation instructions, see 

“Installing an MDA” on page 24

.

Figure 1

 shows the front panels of the 400-4TX MDA and the 

8100-4TX MDA.

Summary of Contents for Media Dependent Adapters 302403-G

































Reviews:

No comments

Brands by name

Popular brands

Load more brands