Nortel 2700 Page 49 Installation Manual Download

Page: 49 / 108

Chapter 2 Cabling the VPN Router and turning the power on

Nortel VPN Router Installation — VPN Router 2700

Single V.35/X.21 WAN interface card LEDs

Figure 18

shows the LEDs on the single V.35/X.21 WAN interface card.

Figure 18

LEDs on the single V.35/X.21 WAN interface card

Table 14

describes the LEDs on the single V.35/X.21 WAN interface card.

Table 14

LED indicators on the single V.35/X.21 WAN interface card

LED

Indicator

Description

LED 1

Red

No external transmit clock source is available.

LED 2

Green

The signals CDC and DSR are on between the DSU

and the adapter. LED 2 detects receive link status.

LED 3

Green

Power to the adapter is on and the onboard

microcode is loaded.

LED 4

Green

Cable is detected.

LED 4, Green

LED 3, Green

LED 1, Red

LED 2, Green

Summary of Contents for 2700













































































































Search results

Summary of Contents for 2700

Reviews:

Related manuals for 2700

Brands by name

Popular brands

Nortel 2700, Installation Manual

Search results

Summary of Contents for 2700

Reviews:

Related manuals for 2700

Brands by name

Popular brands