background image

Doc No. 700016  Page 4 of 16 

 

COLOUR CODE 

VSX2M 

20/25/30 

VSX3M 

30/35/40/

45 

VSX4M 

45/50 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

U Bend 

Inner  
Reflectors 

Outer 
Canopy 

Heat 
Exchanger 

1x 

1x 

1x 

1x 

COLOUR CODE 

VSX2M 

20/25/30 

VSX3M 

30/35/40/

45 

VSX4M 

45/50 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1x 

1x 

2x 

3x 

2x 

3x 

Inner End 
Caps 

Outer  
Canopy 
End Caps 

Tubes 

Couplers 

2x 

2x 

2x 

2x 

2x 

2x 

3x 

2x 

2x 

Brackets 

3x 

4x 

Burner 

8x 

6x 

2.3  Identification check list

 

2x 

1x 

1x 

1x 

4x 

4x 

5x 

2x 

2x 

4x 

3x 

4x 

10x 

M8 
Full Nut 

16x 

22x 

28x 

No.5 
Torque 
Screw 

13x 

14x 

15x 

Turbulators 

2.2.6 Burner and Heat Exchanger 
Assembly. 
 

Slide the burner assembly onto the 

RIGHT 

HAND TUBE 

when viewed from above

ensuring it is fully engaged.  

 

Slide heat exchanger onto the 

LEFT HAND 

TUBE 

when viewed from above

ensuring it 

is fully engaged. The hose connections 

should face vertically. 
 
Secure both assemblies with grub screws. 

M8 U Bolt 

M6 
Mudwasher 

M4 x 10 
Pozi Setpin 

16x 

8x 

12x 

7x 

20x 

9x 

Summary of Contents for Ambirad Vision VSX

















Reviews: