Noritz Eco TOUGH NRCP111-DV-LP Installation Manual Download Page 35

Page: 35 / 44

Gas Supply Piping

Cold Water Supply

Hot Water

Quick Connect Cord

Connector on PCB

Distance on sides

2 - 18 in. (50 - 457mm)

Distance at center : 18 - 36 in. (459 - 916mm)

Leave enough clearance around the plumbing to

apply insulation. It will be necessary to add

bends to the piping to ensure that this clearance

is available.

Pressure

Relief Valve

Shutoff Valve

Gas Valve

Union

Hot Water

Cold Water

Size the piping to allow for the

maximum flow rates of the units.

The backflow preventer is

put up before it diverges.

Quick Connect Cord

Make this distance as short

as possible.

* The hot water temperature

will become unstable as the

pipe length increases

Quick Connect

System Diagram

Typical Plumbing

The Quick Connect Cord is 6 ft.(1.8m) long. Install the units 2-18” (50 - 457mm) apart from each other to ensure the

cable will be able to reach between the units. (See Typical Plumbing diagram). (If the distance between the two units is

too great, not only the cable won’t be able to reach, but the water temperature may also become unstable because of

the difference in pipe length between the two units).

ㆍ

Quick Connect Multi System cannot allows more than 2 units.

ㆍ

All units within Quick Connect Multi System must be of the same model.

ㆍ

Different models cannot work as Quick Connect Multi System.

• Insulate the hot water piping to prevent

heat loss. Insulate and apply heating

materials to the cold water supply piping

to prevent heat loss and freezing of

pipes when exposed to excessively cold

temperatures.

Chapter 4. – Installation

4-9. Quick Connect Multi System Installation

The Quick Connect Multi System allows the installation of two units together utilizing only the Quick Connect Cord.

Summary of Contents for Eco TOUGH NRCP111-DV-LP













































Search results

Summary of Contents for Eco TOUGH NRCP111-DV-LP

Reviews:

Related manuals for Eco TOUGH NRCP111-DV-LP

Brands by name

Popular brands

Noritz Eco TOUGH NRCP111-DV-LP, Installation Manual

Search results

Summary of Contents for Eco TOUGH NRCP111-DV-LP

Reviews:

Related manuals for Eco TOUGH NRCP111-DV-LP

Brands by name

Popular brands