background image

18

Application Notes & Heat Mode Verification Tables (Heat Mode Only)

•  Read all notes and warnings for the Cooling-mode 

charging charts prior to using these Heating-mode 

charge verification charts. Always use safe and 

environmentally sound methods when handling 

refrigerant handling or servicing the unit. Review 

the factory literature and safety warnings prior to 
servicing.

•  When repairing system leaks, always use a nitrogen 

(inert) gas to protect the refrigerant system and pressure 

check the repair before re-charging. Always replace 

the filter-dryers when performing any repair to the 

refrigeration system with one capable of acid removal. 

After completing the repairs, evacuate the system to 

350 - 500 microns and weigh in the refrigerant to the 

amount specified on the unit rating label.

•  Before  using  the  heat  mode  verification  tables, 

determine the outdoor ambient temperature and the 

return air temperature to the unit. Locate the appropriate 

location on the units verification chart based on those 

measurements to determine the ideal discharge 
pressure and temperature. See 

Table 12 (page 19)

Table 13 (page 19)

Table 14 (page 19)

Table 15 

(page  19)

Table 16 (page 20)

Table 17 (page 

20)

, & 

Table 18 (page 20)

. Verify the outdoor fan 

and compressor are running and the outdoor coil is 

free from frost accumulation. Also verify the system 

is not operating in defrost mode before inspecting the 

system.

•  Always use quality instruments that are in good working 

order to measure the actual operating point of the 

refrigeration system. The discharge temperature should 

be within 2 degrees of the ideal value and the pressure 

should be within 2%.

•  The most reliable way of verifying the system is at the 

correct charge is to evacuate the system and weigh 

in the charge to the amount shown on the rating label. 

However, if an inspection with these verification charts 

does not line up with the values shown and the ambient 

temperature is above 50˚ F, then a more accurate 

way to inspect the system for proper charge is with 

the cooling mode charging charts. Switch the unit into 

cooling mode and allow it to operate and stabilize for 

a few minutes then inspect the unit operation with the 
cooling mode charts and procedures.

  Before changing the unit charge, always inspect 

the following items first:

1. Inspect the liquid line temperature on the inlet and outlet 

of the filter dryers. If it is the factory dryer and in good 

condition there should be no temperature difference. 

If the temperature difference is larger than 5˚, replace 

the filter dryer with one that is bi-directional and has 

acid removal capability. Refer to the unit RPL for the 

recommended part number and size.

2. Inspect the units input voltage. Units operating at less 

than 95% of the nominal voltage may deviate more from 

the chart then previously stated.

3. Inspect the input voltage for a phase imbalance. Units 

with greater then a 2% disparity will not operate at the 

rated performance.

4. Verify that the unit filters are installed and are clean. 

The pressure drop across the filters should not exceed 

0.08 in-W.C.

5. Inspect the indoor coil, indoor blower and blower motor 

for cleanliness, clogging, and proper operation.

6. Inspect the system for leaks. If any leaks are detected, 

repair them immediately. Re-inspect the return air and 

ambient temperatures and verify that the correct system 

point on the verification chart was selected.

DO NOT

 use the charts in systems that have the fan cycling 

under a low-ambient control. Low-ambient controls are 

for cooling operation. In heating mode, the low ambient 

control should be disabled. Unless the unit is in defrost 

mode, the outdoor fan should always operate in conjunction 

with the compressor.

IMPORTANT NOTE:

If the unit is equipped with a liquid valve with an 
outdoor restrictor as shown in 

Figure 2 (page 4)

then it is not possible to measure the liquid pressure. 

To approximate the liquid pressure, subtract 7 psig 

from the discharge pressure.

 

Shaded boxes indicate flooded conditions.

 

Rated design values. The suction pressure will vary from design value if outdoor air flow, entering dry 

bulb, or entering wet bulb temperatures vary.

1. All pressures are listed in psig and all temperatures in ° F

2. Discharge temperatures greater than charted values indicate an undercharged system.

Summary of Contents for T4BE-018 Series

























Reviews: