background image

8

Air From Inside

If combustion air is taken from the heated space, the two 
openings must each have a free area of at least one square 
inch per 1,000 Btuh of total input of all appliances in the 
confi ned space, but 

not less than 

100 square inches of 

free area

 

(Figure 5). For example, if the combined input 

rate of all appliances is less than or equal to 100,000 
Btuh, each opening must have a free area of at least 100 
square inches. If the combined input rate of all appliances 
is 120,000 Btuh, each opening must have a free area of 
at least 120 square inches.

Installation In An Unconfi ned Space

An unconfi ned space is an area including all rooms not 
separated by doors with a volume greater than 50 cubic 
feet per 1,000 Btuh of the combined input rates of all 
appliances which draw combustion air from that space.

In general, a furnace installed in an unconfi ned space will 
not require outside air for combustion. However, in homes 
built for energy effi ciency (low air change rates), it may 
be necessary to provide outside air to ensure adequate 
combustion and venting, even though the furnace is located 
in an unconfi ned space. See example.

Air Directly Through An Exterior Wall

 

If combustion air is provided directly through an exterior 
wall, the two openings must each have free area of at 
least one square inch per 4,000 Btuh of total appliance 
input (Figure 4).

Figure 4. Combustion Air Drawn from Outside 

Through an Exterior Wall

-----

----

-----

----

12" Max

12" Max

Furnace

NOTE:

 Each opening 

to outside must be at 
least 1 sq. in. per 
4,000 Btuh of total 
input rating.

Vent or 
Chimney

Water Heater

See 
Note

Total Input Rating 

(Btuh)

Minimum Free Area

 (Each Opening)

Round Duct 

Diameter

40,000

10 sq. In

4 inches

60,000

15 sq. In

5 inches

80,000

20 sq. In

5 inches

100,000

25 sq. In

6 inches

120,000

30 sq. In

6 inches

140,000

35 sq. In

7 inches

160,000

40 sq. In

8 inches

Furnace

12" Max.

Water

Heater

Vent or 

Chimney

NOTES:

 

Each opening must 
be at least 100 sq. in.
or 1 sq. in. per 1,000 
Btuh of total input rating, 
whichever is greater. 

Openings must start at
no more than 12 inches
from the top and bottom
of the enclosure.

12” Max.

See 

Notes

See Notes

Figure 5. Combustion Air Drawn from Inside

Total Input Rating 

(Btuh)

Minimum Free Area

 (Each Opening)

Round Duct 

Diameter

40,000

100 sq. In

12 inches

60,000

100 sq. In

12 inches

80,000

100 sq. In

12 inches

100,000

100 sq. In

12 inches

120,000

120 sq. In

13 inches

140,000

140 sq. In

14 inches

160,000

160 sq. In

15 inches

Alternate Method of Providing Air from Outside:

If acceptable under local Codes, it is permitted to 
provide outside air using one opening (See NFGC).

Generally, confi ned spaces must have two openings 
in the space for combustion air. One opening must 
be within 12 inches of the ceiling, and the other 
must be within 12 inches of the fl oor. However, an 
alternative method recently adopted by the NFGC 
uses one opening within 12 inches of the top of the 
space. This method may be used if it is acceptable 
to the local codes.

The following conditions must be met:

1. The opening must start within 12” of the top of the 

structure and connect with the out of doors through 
vertical or horizontal ducts or be ducted to a crawl 
or attic space that connects with the out of doors.

2. The opening must have a minimum free area of 1 

sq. in. per 3,000 Btu per hour of the total input rating 
of all equipment located in the enclosure.

3. The free area must not be less than the sum of all 

the areas of the vent connectors in the enclosure.

Example

:

A space with a water heater rated at 45,000 Btuh 
input and a furnace rated at 75,000 Btuh requires a 
volume of 6,000 cubic feet [50 x (45 + 75) = 6,000] to 
be considered unconfi ned. If the space has an 8 foot 
ceiling, the fl oor area of the space must be 750 square 
feet (6,000 / 8 = 750).

Summary of Contents for 045C-23ASA





































Reviews: