background image

Safety

1-5

Part 104373

04

E

 2017 Nordson Corporation

Safety Labels 

See Figure 1-1 for the location of the safety labels.  Figure 1-2 displays the

main safety label (1).  Table 1-1 describes the remaining safety labels (2, 3).

Figure 1-3 displays the ATEX patent label.

Safety labels are provided to help you operate and maintain your

equipment.

2

1

3

3

Figure 1-1

Safety Label Locations

D

 HIGH PRESSURE DEVICE

Read instruction manual before operation and observe all warnings.

D

 INJECTION HAZARD

Airless spray painting equipment can cause serious injury if the spray

penetrates the skin. Do not point the gun at anyone or any part of the body. In

cases of penetration, adequate medical aid must be immediately obtained.

D

 COMPONENT RUPTURE

This system is capable of producing 104 BAR (1500 PSI) pressure. To avoid

rupture and injury, do not operate this pump at a pressure higher than the rated

maximum working pressure of any component in the system (including but not

limited to spray guns, hoses, hose connections, and heaters).

D

 FIRE

Static voltage is developed by airless spraying. The pump, associated system,

and object being sprayed must be grounded to prevent static discharge sparks

which could start a fire.

D

 SERVICING

Before servicing, cleaning, or removal of any part, set trigger lock on gun, and

always shut off power source; then carefully release pressure in fluid portions

of the system.

MODEL

PART NO.
RATIO
SERIAL NO.

NORDSON CORPORATION  AMHERST, OH 44001

Figure 1-2

Main Safety Label

Summary of Contents for cp




















































































Reviews: