Nordmann DC4 Operating Instructions Manual Download

Page: 14 / 56

Operation

Proceed as follows when putting the unit into operation:
1.

Examine the steam humidifier and installation for possible damage

DANGER!

Damaged devices or devices with damaged installation may present danger to human life or

cause severe damage to material assets.

Damaged units and/or units with damaged or faulty installation must not be operated.

2. Check whether the front panel is mounted and fixed with the screw.
3. Open the

filter valve

(or the shut-off valve, respectively) in the water supply line.

4. Verify the set humidity value at the humidity controller or at the humidistat, and readjust as re-

quired.

Switch on the service switch

for mains supply.

Actuate the unit switch

of the steam humidifier.

Switch lights up

4.1

Commissioning

The steam humidifier carries out a

system test

, during which all the LEDs

light up and the opposite display is shown.
If a failure occurs on the system test, a corresponding error message is

shown in the display.

After the system test the unit is in

normal operation mode

. The display

shows the

standard operating display

(first page of the indication level).

Note: The contents of the standard operating display depends on the actual

operating status and on the configuration of the Nordmann RC4/DC4 and

can differ from the opposite display.

As soon as the humidity controller or the humidistat requires humidity, power

is switched on for heating. The inlet valve opens (slight delay) and the steam

cylinder fills with water. As soon as the submerged electrodes heat the water

up the green LED lights up and after a few minutes (approx. 5–10 minutes,

depending on the conductivity of the water) steam is produced.

Note: If the Nordmann RC4/DC4 is operated with water of low conductivity it may happen that

the maximum steam capacity is not reached in the first few hours of operation. This is normal.

As soon as the conductivity has reached a sufficient level (due to the vaporisation process) the

humidifier will reach the maximum steam capacity.

STARTUP:

RC4/DC4

INIT MODULE

RC4 230V2

Standby

2011-10-31 12.00.00

RC4 230V2

Demand :100%

2011-10-31 12.00.00

Summary of Contents for DC4

























































Search results

Summary of Contents for DC4

Reviews:

Related manuals for DC4

Brands by name

Popular brands

Nordmann DC4, Operating Instructions Manual

Search results

Summary of Contents for DC4

Reviews:

Related manuals for DC4

Brands by name

Popular brands