Nokia NPD-1 Series Troubleshooting - Rf Download Page 26 | Manualshive

Page: 26 / 62

background image

NPD-1

Troubleshooting — RF

CCS Technical Documentation

Page 26



Nokia Corporation Confidential

Issue 1 11/2002

Troubleshooting: If transmitted power levels can not be attained, check PCS TX as
described at the beginning of this chapter.

TS ACPR Cell - Low

See description for PCS ACPR. In cell band, however, the offset is –0.9 MHz (+ 0.9 MHz).

See TN TX Limiting Po Cell (or PCS) IS 95 section for an explanation of results.

Manual Verification: Set up the measurement as described in the TN TX Limiting Po Cell
(or PCS) section, but turning on the Cell transmitter to channel 384. Likewise, use the
TxdBCtr value for Cell TX Limiting on channel 384 in IS95 mode. Measure at the center
frequency of 836.52 MHz, and the offset of +/- 0.9 MHz.

Troubleshooting: Refer to the TN TX Limiting Po Cell (or PCS) IS95 section, and also the
Cell TX troubleshooting guide of the Probing/Troubleshooting Tables and Diagrams sec-
tion. Cell band TX decoupling capacitors are C653, C633, C649, C648, C619, C817, C810,
and C811.

TN RX IF AGC RXdBCtr (0) [or (1) or (2)]

This tuning calibrates the RX IF AGC curve since the output power of the IF part of the
Batman IC is not a linear function of RX_IF_AGC. The tuner injects three known signal
power levels into the phone’s receiver, and for each one the phone’s AGC algorithm
adjusts the RX_IF_AGC to get the same amplitude at the output of Batman, although
different amplitudes are going in. From these three points, curve fitting is used to inter-
polate between measurement points.

The result is a value of RxdBCtr (which corresponds to a value of RX_IF_AGC) for each of
three CW input powers injected into the receiver:

TxdB Ctr Value

Transmitted power (in dBm)

(TxdBCtr for TX limiting) + 350

Check tuning results file for limits

(TxdBCtr for TX limiting) - 500

(TxdBCtr for TX limiting) - 1000

(TxdBCtr for TX limiting) - 1500

(TxdBCtr for TX limiting) - 3200

(TxdBCtr for TX limiting) - 4200

Trimode

PCS only

-87.5 dBm

-89 dBm

-57 dBm

-61 dBm

«
...
24
25
26
27
28
...
»

Summary of Contents for NPD-1 Series































































Reviews:

No comments

Related manuals for NPD-1 Series

Brand: Xorcom Pages: 2

Brand: i-mobile Pages: 72

Brand: Olitech Pages: 12

Brand: Polycom Pages: 2

Brand: INQ Pages: 101

Brand: PalmMicro Pages: 40

One Touch Spop 4030D

Brand: Alcatel Pages: 73

Digital Mova SO503iS HYPER

Brand: Docomo Pages: 396

Brand: HTC Pages: 139

Brand: Grandstream Networks Pages: 53

Brand: Grandstream Networks Pages: 2

Brand: Iget Pages: 63

Brand: Samsung Pages: 182

Brand: Samsung Pages: 193

Brand: Samsung Pages: 2

SGH-T519 - Trace Cell Phone

Brand: Samsung Pages: 141

Brand: Samsung Pages: 178

Brand: Samsung Pages: 174

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands