Nokia 603 Service Manual Download Page 51

Page: 51 / 226

Table of Contents

.........................................................................................................................

3–5

Power and charging troubleshooting

.................................................................................................................

3–9

Backup battery troubleshooting

.....................................................................................................................

3–9

General power checking troubleshooting

.....................................................................................................

3–9

Dead or jammed device troubleshooting

...................................................................................................

3–10

USB charging troubleshooting

.....................................................................................................................

3–11

Interface troubleshooting

.................................................................................................................................

3–13

USB flashing fault troubleshooting

.............................................................................................................

3–13

USB data interface troubleshooting

............................................................................................................

3–14

SIM card troubleshooting

.............................................................................................................................

3–14

MicroSD card troubleshooting

......................................................................................................................

3–16

IVE troubleshooting

...........................................................................................................................................

3–17

Introduction to IVE troubleshooting

...........................................................................................................

3–17

IVE troubleshooting

......................................................................................................................................

3–18

Display module troubleshooting

......................................................................................................................

3–18

General instructions for display troubleshooting

......................................................................................

3–18

Introduction to display troubleshooting

....................................................................................................

3–20

Display fault troubleshooting

......................................................................................................................

3–21

Touch panel troubleshooting

.......................................................................................................................

3–21

Illumination troubleshooting

......................................................................................................................

3–23

Charging illumination troubleshooting

.................................................................................................

3–23

Keyboard backlight troubleshooting

.....................................................................................................

3–23

Keyboard troubleshooting

................................................................................................................................

3–25

Sensors troubleshooting

...................................................................................................................................

3–26

Accelerometer troubleshooting

...................................................................................................................

3–26

Magnetometer troubleshooting

..................................................................................................................

3–26

Proximity technical description and troubleshooting

...............................................................................

3–27

Proximity tuning

...........................................................................................................................................

3–28

Ambient Light Sensor (ALS) technical description and troubleshooting

.................................................

3–29

Audio troubleshooting

.......................................................................................................................................

3–30

Audio troubleshooting test instructions

.....................................................................................................

3–30

External earpiece troubleshooting

..............................................................................................................

3–32

External microphone troubleshooting

........................................................................................................

3–33

Internal earpiece troubleshooting

..............................................................................................................

3–34

Internal handsfree (IHF) troubleshooting

...................................................................................................

3–35

Internal microphone troubleshooting

........................................................................................................

3–36

Acoustics troubleshooting

............................................................................................................................

3–37

Introduction to acoustics troubleshooting

...........................................................................................

3–37

Earpiece troubleshooting

........................................................................................................................

3–38

IHF troubleshooting

.................................................................................................................................

3–38

Microphone troubleshooting

..................................................................................................................

3–40

Vibra troubleshooting

...................................................................................................................................

3–41

Connectivity module troubleshooting

.............................................................................................................

3–41

Introduction to connectivity module troubleshooting

.............................................................................

3–41

Bluetooth/FM radio and WLAN troubleshooting

........................................................................................

3–44

Introduction to Bluetooth/FM radio troubleshooting

..........................................................................

3–44

Introduction to WLAN troubleshooting

.................................................................................................

3–46

Bluetooth and FM radio self tests in Phoenix

.............................................................................................

3–47

WLAN self test in Phoenix

.............................................................................................................................

3–48

Bluetooth BER test in Phoenix

.....................................................................................................................

3–48

RM-779

BB Troubleshooting and Manual Tuning Guide

Issue 1

COMPANY CONFIDENTIAL

Page 3 – 3

Summary of Contents for 603






































































































































































Search results

Summary of Contents for 603

Reviews:

Brands by name

Popular brands

Nokia 603, Service Manual

Search results

Summary of Contents for 603

Reviews:

Brands by name

Popular brands