Nokia 603 Service Manual Download Page 68

Page: 68 / 226

Item

Bright dot (sub-

pixel) defect

Dark dot (sub-

pixel) defect

Total

Temporal sub-

pixel defect

Not allowed

Note:

Blinking pixels are not allowed in normal operating temperatures and light conditions.

Introduction to display troubleshooting

The display module used is based on TFT technology and supports display format of 360 columns x 640 rows.

The dimension of the display module is 43.2 mm x 76.8 mm x 1.8 mm. The module will interface to the phone

via FPC with a 25 pins ZIF connector.
The following references on the PWB help in the effective debugging and troubleshooting of the display.

Sr No

Reference

Description

X1650

Display connector

Z1620, Z1621

Common Mode Choke on DSI bus

D1400

BCM2763 IC

The following test points on the PWB help in the effective debugging and troubleshooting.

Sr. No

Signal name

Measuring point

Description

VIO

L1620/C1620

1.8V supply to display

VAUX1

L1621/C1622

VAUX1 supply to display

RM-779

BB Troubleshooting and Manual Tuning Guide

Page 3 – 20

COMPANY CONFIDENTIAL

Issue 1

Summary of Contents for 603






































































































































































Search results

Summary of Contents for 603

Reviews:

Brands by name

Popular brands

Nokia 603, Service Manual

Search results

Summary of Contents for 603

Reviews:

Brands by name

Popular brands