V1.0.0
51
Brake System
Brake liquid change/air discharging (for the disc brake type)
Drainage of the brake liquid
The paint coatings, plastics or rubber parts should be covered with cloths as good as possible to avoid
splash of the brake liquid onto them in changing the system liquid or draining the liquid.
There should be no foreign matters that enter into the system in liquid injection into the liquid reservoir.
Turn the steering handle until the liquid reservoir on main oil cylinder becomes horizontal, before
removal of the main oil cylinder cover.
Remove screws, oil cylinder cover and oil pan cover from the main oil cylinder on front brake.
Connect the oil drainage hose to the oil drainage screw on front brake caliper.
Loosen the oil drainage screw and grasp the front brake handle tightly until
the brake liquid does not flow out from the oil drainage screw.
Brake liquid injection/air discharging
Add the DOT3 or DOT4 brake liquid into the liquid reservoir, and add it to the upper limit of the liquid level.
Note
:
Do not use different types of the brake liquid because they are not compatible with each other.
Connect air discharge pump from the brake liquid to the oil drainage valve screw.
Operate the air discharge pump from brake liquid, and loosen the oil drainage screw.
Check the brake liquid level frequently in air discharging to avoid air entrance into the hydraulic system.
Perform the discharging operation procedure strictly until the air discharging from hydraulic system is completed.
Seal thread of the oil drainage screw with a PTFE adhesive-tape, if the air can enter into the air discharge pump through the th
Tighten the oil drainage screw, and operate the brake handle. Repeat the air discharging operation if there
is still a soft feeling.
Tighten the oil drainage screw on brake caliper after the air has been discharged completely.
Screw
Main oil cylinder
cover
Oil pan cover
Summary of Contents for N-GT
