manualshive.com logo in svg

Nippon Genetics FASTGENE ELECTRONIC PIPETTE-10, Manual

Share
Download
Nippon Genetics FASTGENE ELECTRONIC PIPETTE-10 Manual Download Page 8

 

NIPPON Genetics EUROPE – www.nippongenetics.eu 

8 

8. 

8-1 

Installing the battery 

1.

 

Remove  the  battery  cover  (2)  by  sliding  it  upward  while  pressing  and  holding  the  battery 
cover release button (1). 

2.

 

Connect the terminal of the battery’s cable, as shown in the figure below, to the connector for 
the  battery  in  the  bottom  of  the  battery  compartment.  When  connecting  the  terminal,  be 
sure it is connected in the proper direction. 

3.

 

Install the battery so that the battery cable is in the cable guide. 

4.

 

Attach the battery cover on the pipette by sliding it downward from the upside. 

 

 

 

 

 
 
 
 
 
 

 

1. Open the battery cover.

           

2. Connect the battery connector. 

 
 
 
 
 
 
 
 
 

 

3. Install the battery.                                4. Attach the battery cover.

 

 

Note:  When  connecting  the  battery  to  the  pipette,  all  illuminations  on  the 

display  illuminate  and  the  pipette  built-in  piston  automatically  goes  to  the 

initial default position. If a key is pressed, the pipette goes into the operating 

mode. 

 

(1) 

(2) 

Expanded 

Cable 

Cable guide 

Red 

Black 

Battery cover 

Battery cover 

release button 

Battery connector 

Summary of Contents for FASTGENE ELECTRONIC PIPETTE-10





































Reviews:

No comments

Brands by name

Popular brands

Load more brands