manualshive.com logo in svg

NimbeLink NL-M1DK, User Manual

Share
Download
NimbeLink NL-M1DK User Manual Download Page 4

 

1. Introduction 

1.1 Overview 

This document is the User Manual for the NL-M1DK, NL-SW-LTE-SVZM20-ES, 
and NL-SW-LTE-SVZM20 family of Skywire® modems. The procedure outlined in 
this guide walks through installing the Skywire modem, setting up your 
workstation, issuing basic commands, and registering on the Verizon network. 

1.2 Orderable Parts

 

Table 1.1 Orderable Parts

 

Number

 

Description

 

Firmware 

Manufacturer

 

Carrier

 

NL-M1DK 

Skywire 4G LTE CAT M1 
Development Kit 

 

NimbeLink 

Verizon 

NL-SW-LTE-SVZM20-ES 

Skywire 4G LTE CAT M1 
Cellular Modem 

30850 

NimbeLink 

Verizon 

NL-SW-LTE-SVZM20 

Skywire 4G LTE CAT M1 
Cellular Modem 

32110 

NimbeLink 

Verizon 

NL-SW-LTE-SVZM20-B 

Skywire 4G LTE CAT M1 
Cellular Modem 

37120 

NimbeLink 

Verizon 

NL-SIM-VER-M1 

3FF Verizon LTE CAT M1 Sim 
Card 

 

NimbeLink 

Verizon 

TG.30.8113 

Dipole Cellular Antenna 

 

Taoglas 

 

TG.08.0113 

Monopole Cellular Antenna   

Taoglas 

 

1.3 Firmware Changes 

The chipset manufacturer has released a new version of firmware - firmware version

 

 

 

 

   

 

   

   

 

 

37120 - that makes available some features and fixes many issues. Here is a brief

   

 

 

 

 

 

 

 

 

 

     

 

description of the firmware changes: 

-

More AT command are enabled and functioning. We have an AT command

 

 

 

 

 

 

 

 

 

 

 

 

manual available on our website: 

http://nimbelink.com/Documentation/Skywire/4G_LTE_Cat_M1/1001534_NL-SW-
LTE-SVZM_AT_COMMAND_MANUAL.pdf

 

-

Low power modes are enabled, and an application note explaining the process is

 

 

 

 

 

   

 

 

 

 

   

located here: 

https://nimbelink.com/https://nimbelink.com/skywire-4g-lte-cat-m1/1001779_NL-S
W-LTE-SVZM20_LowPowerAppNote.pdf

 

-

Bug fixes and lockup fixes 

-

Addition of a client to communicate with Verizon Thingspace 

-

The USB port can now be used as an AT command port. 

PN 30192 rev 10

© NimbeLink Corp. 2018. All rights reserved.

4 

Summary of Contents for NL-M1DK

























Reviews:

No comments

Brands by name

Popular brands

Load more brands