USER MANUAL
33014816(1)2005-07 A
11
PROBLEMS AND REMEDIES
The following table shows the most common problems that may arise during the use of the machine, the possible causes and
the suggested remedies to solve them.
PROBLEMS AND REMEDIES
WARNING!
When applying a recommended solution, always follow the instructions relating to it.
NOTE
Do not hesitate to contact Nilfisk-Advance if a problem cannot be solved by following the instructions
provided.
PROBLEM
CAUSE
REMEDY
Heavy material not collected/traces of dirt
left behind during use
Excessive drive speed
Decrease drive speed
Light print
Adjust print
Worn out broom
Replace the brooms
Broom bristles bent or tangled with steel wire,
ropes etc.
Remove any tangled material
Excessive amount of dust left on the ground
or coming out of skirts
Fan off
Switch on the fan
Clogged filters
Clean filters
Material is thrown forward
Broken skirt gasket
Replace
Engine fails to start
Blown general fuse
Replace fuse
Blown safety fuse
Replace fuse
Discharged battery
Charge battery
Machine power is reduced
Insufficient pump oil feed
Check by-pass screw tightening
Check pump pressure (16 to 20 Bar)
Overhaul pump
Worn motors
Overhaul motor
Machine fails to run
Open by-pass
Check by-pass screw tightening
Faulty pedal
Replace pedal
No power to pump or motors
Overhaul pump
Overhaul motor
Machine fails to brake
No brake fluid
Top up fluid tank
Brake fluid pump failure
Overhaul pump
Air inside the system
Bleed system
Jaw cylinders failure
Replace cylinders
Worn or greasy brake lining
Replace brake lining
Hard power steering
Locked power steering
Replace power steering
Priority valve failure
Overhaul/replace priority valve
Hopper fails to lift/lower
Locked distributor
Check distributor
Locked cylinder
Check cylinder
Waste loss from hopper
Broken hopper gasket
Replace gasket
Filter shaker fails to operate
Broken push-button
Replace
Blown fuse
Replace
Excessive motor absorption due to:
– Worn carbon brushes
– Dirty or worn bearings
– Burnt armature or winding
Replace
Replace
Replace
Blown filter shaker fuse
Excessive motor absorption
see above
Faulty fuse
Replace
Shorted cables
Check system
Noisy fan
Motor failure
Overhaul motor
Fan fails to operate
No voltage to motor
Check electrical system
Motor failure
Overhaul motor
Skirt fails to open
No pressure to cylinder
Check system
Locked linkage
Check linkage
Skirt gasket lifted by broom
Gasket is too long
Shorten/replace
Summary of Contents for SR 1700 2WD B
